Case 850G Operation?

I just bought a Case 850G and had a few questions about operating it correctly (No luck finding a manual). I will be using it to clear about 100-150 acres of brush and clear fence rows. After that maybe build a road or two and clean out a few pools.
#1 I think I have the turn levers figured out but am not really sure if it hurts to use the brakes to turn rather than the levers? Also I'm guessing you just shift them at full throttle like a Cat powershift.
#2 It doesn't have a decelarator pedal. Can you just shift forward and reverse at full throttle or do most people use the foot pedal to run the dozer?
The dozer has 3400 hours on it and seems to be in good shape. I plan on servicing it and cleaning it up good this week. I like to keep equipment fairly clean and leak free if possible. Thanks for any help.

Case 850G Operation?

690 ELC electrical problems

I have a 690 elc I have had for many years. Has always worked fantastic until this summer. Started having problems with mode control. Any time I changed modes or engine speed all hydraulics would cease functioning. Would have to go back to idle and slowly work it up to speed using a function as I raised speed. This was some what of an intermittent problem until today. All power to the function controls quit. No lights or controls of any kind. Engine starts fine and excavator moves but no engine speed control. Idle only. Have checked wiring and everything seems fine. No frayed wires or loose connections. Can this be a malfunctioning monitor controller? Can anyone help me with this problem?

690 ELC electrical problems

1994 JCB Sitemaster Fan/Drive Belt Install

So I tore a fan belt(s) today running the Backhoe (94 Sitemaster 4x4 with AC) So I see that I need 3 Belts, 1 smaller drive bent for the AC (which is beat up but still in tact), and 2 larger belts for the fan. I have two questions:

1) Since this thing does not really have AC (All the glass was vandalized years ago) Do I "need" the smaller drive belt that pumps the AC? I can't for the life of me remove the (4) 10mm bolts on the front of the fan which I will have to do for the smaller belt, but access is a B$ich. I think I can get the larger belt around it if I had to, I already removed the lower shaft for the Hyd Pump. If I have to have the smaller belt any hints on removing the fan?

2) Do these two larger belts PN 01/124405 come as a pair? http://ift.tt/1QRAKYr

-On the website it says (pair) but does that mean it includes 2 belts? Or saying I need two? I mean for 20.00 I figure its just one belt. I will just get a number off the belt and get one at Napa auto parts probably.


Thanks!:notworthy

1994 JCB Sitemaster Fan/Drive Belt Install

96 963b engine normal opperating temp

Hello I have a oil leak, I believe at the harmonic balancer seal, on a warm day temp climes to 220 then it appears oil thins out and leaks faster oil gets slung into the fan and sprays on radiator then dust clogs radiator and it leaks more oil the hotter it gets. I am running a 15-40wt the question could i use a thicker oil or an additive, help?? and what is the temp level before i shut it down, my gauge tops out at 140 degrees, dummy lights do not work anymore.

96 963b engine normal opperating temp

t770?

Really wondering if a bobcat t770 would be the right machine. I'm very new to the equipment market so any input is appreciated But I'm looking for a machine that would be good for forestry mulching in fairly hilly areas. Would that be a good machine for that type of work? Or is there something that would be much better?

t770?

grove tms 500 boom grease fittings

just discovered this awesome forum im starting to like my pc hoping someone here can help me locate the grease fittings for the retract sheaves at the heal of the boom the manual says there are 4 located at the heal of the boom accessed from holes on the sides no holes there i found an access cover on top was able to find the sheaves and only 2 fittings inboard are there any more ? thanks in advance

grove tms 500 boom grease fittings

Need help identifying dozer

The man I bought my land from is a large farmer . He has a large dozer on his land that needs the injection pump replaced . The man that took it off passed away so itS been sitting for two years . The model number on side I cannot find anywhere online trying to find pertinent information for repairs etc. I have never worked on a dozer but am a mechanic for a living and do a lot of diesel work so told him I would do my best . Both sides say 9774 by the cat logo . I will upload pictures if I can figure out how !

Need help identifying dozer

JD 455G 2nd Gear

Weather finally broke and got a chance to work with the 1995 455g Loader. Saturday was fine but today seem to have lost 2nd gear forward and back. 1st and 3rd are fine but 2nd goes in sporadically but not for the most part.

Any ideas where to start? I rarely run this machine so it sits for long periods at a time.

Thanks,
Tom

JD 455G 2nd Gear

1979 cat 930 wheel loader steering issues

i have a cat 930 wheel loader that i just recently changed the hydraulic pump cartridges in. had no problems with the steering until now. when i first changed the pump cartridges they were clocked opposite directions from how the original ones came out. could something be stuck in thr steering valve assembly? there is no leaks or sounds just seems like there is no pressure at the wheel and its very difficult to turn. need any advice asap please and thank you

1979 cat 930 wheel loader steering issues

Pad relief holes

Can anyone tell me if I need to cut relief holes in my pads for pushing snow. Just bought a Case 450 dozer without the relief hole. My D4D had holes cut should not have sold it. Just wondering how important it is. I see some with and some without?
Thanks David

Pad relief holes

Allison transmission H6610

Hello !
Can any help me with Allison transmission, we have dump track DP705 with Allison transmission and it slow shift in range of speed, with load and slope terrain will not shift in higher speed. There aren't any codes on display and wiring is OK. Which value of pressures on Allison transmission (torque IN-OUT, lockup clutch, clutches of speed etc.) ?
Thanks !

Allison transmission H6610

cat 416b 1995 4wd issuses

New to forum. 4wd not working. Wire #143 going to the 4wd switch has 13.5volts when tested, however when I add a test light to it the voltage drops to zero. Don't understand why it drops to zero and not light the test light. Thanks mark

cat 416b 1995 4wd issuses

Selecting undercarriage

Hi guys! I want to ask a question. Which brand undercarriage do you prefer?I did not find a topic here.
In Russia the most popular (in declining order):
1. Berco
2. Original
3. ITM
4. ITR and other Chinese and Korean brands

Selecting undercarriage

1998 gradall excavator xl 4100 hydraulics not working

Was wondering if anyone seen this problem? The engine in the upper deck idles up but I dont have any of the hydraulics working and the gradall will not move either from the upper deck motor. The gradall will drive from the lower engine but when you are going to work from the top engine the hydraulics will not function. I changed the hydraulic filters and still nothing. The pump drive that mounts behind upper deck engine has been replaced and still nothing. This pump drive was replaced because it was all messed up when it was removed to inspect. This is were the pumps get their pressure from the pump drive engaged with the flywheel but still no change in the hydraulics. Anyone worked on these gradalls?:Banghead

1998 gradall excavator xl 4100 hydraulics not working

older 430 case 188 diesel question

Hi all , new poster with not much to offer in the help department but need some advice on a 430 188 diesel head gasket change. The reason i think it is a head gasket as i get pressure in cooling system and some minor engine oil in coolant. No coolant in oil. backhoe starts fine and runs great. I think im hearing a slight sucking sound in exhaust.. I have not noticed any loss in power.. I have checked valve adjustments and such. . I found a suppler that can set me up with the head gasket narrow or large flange .. It just looks like id have to pull water pump to take head off. Any info would be greatly appreciated.
diver

older 430 case 188 diesel question

Case 580L transmission debris

Just bought a 1998 580l with 2850 hours. Whenever I buy a machine I like to change all the fluids and filters. When I drained the transmission pan, the fluid initially was very thick (was cold), but more importantly there was about a thimble full of sludgy metal attached to the drain magnet. When I removed the suction screen there were little black metallic flakes attached to it. Not many. Inside that screen, the magnet had abt half a thimble full, or a little less of magnetic black sludge. I ran a magnet through the drained fluid. All in all I'd say I had just less than a half an ounce of gritty black junk (no silver looking stuff). I'm guessing it had the original Case filter as it said Case. Was very rusty and I needed a 3 ft breaker bar to turn it loose.
The machine had no problem before I switched the fluid and none now. When I put it in first or second it does so with a nice jolt. Feels great. I will say when it's in 3rd or 4th, if there is any rise at all in the road it slows right down. Is this normal? Is the amount of debris just normal wear and tear for a machine that hasn't been serviced since new?
I know I'm probably over thinking this, but I'm loving this machine and want to keep it going for years.
Thanks in advance.

Case 580L transmission debris

allison automatic trains (ptos)

hey guys,,, still in process of finding the rite truck to build my service truck with,,, but ive got a old FL70 with a manual trains. the truck is equipped with a pto for hyd. pump an a pto for the air compressor, was wanting to know if Allison auto.s come with a pto plate on each side of it or just one, another wander is how do ya tell if the trains. has the pto gear in it even if the plates there. I have heard storys of people removeing the plates to put there pto on an there want be a gear in there, kinda like when trains. was built they didn't install gear for future use.:Banghead

allison automatic trains (ptos)

keeping ROOTS out of screens

We're looking to take over a small material pit and much of the remaining area has tree cover. I know from the owner that the roots can damage and screw up screens...I've googled but is there anything to put on a screen plant that will allow us to eliminate roots?

keeping ROOTS out of screens

Concrete curb cuts: vertical or horizontal

I need to remove 30 feet of concrete curb next week so as to tie the current project's new driveway into the street. I met with the state highway fellow yesterday to go over the lane closing plan, and he sort of threw cold water on the cutting operation I had in mind. My concrete sub and I had planned to cut straight down (vertical) along the edge of the asphalt lane for the 30 foot distance, then (after cutting the curb crossways at both ends) use the excavator to pull the curb away from the street. But the state guy said he doesn't think we can cut it deep enough to do this. He says there is two inches of asphalt overlaying the lip (gutter) of the curb, and he doesn't know how thick the lip is. He is afraid that if we don't cut through completely that we will damage the asphalt lane when we pull back on the curb, and it's too cold to repair the asphalt.

So he wants us to try to cut the the top of the curb off horizontal to the top of the asphalt traffic lane. I don't even know if they make a saw that will lay on its side and make this cut.

Any advice for us? To make matters worse, we will have to do the project's second driveway in a couple of weeks in the same manner.

Concrete curb cuts: vertical or horizontal

Tooth bucket for Cat 215 wanted

Anyone have a Cat brand bucket that is 48",54" or 60" wide preferably with teeth that fits a Cat 215 or Cat 225 for sale? Looking for one, location is IL. Thanks!

Tooth bucket for Cat 215 wanted

Dresser TD7G transmission oil

I'm trying to make it a clean sweep of all oil, filters, and maintenance issues with the Dresser before putting it in service. This ain't cheap! Numerous aspects of the tractor differ from the manual. The thing of greatest concern is fluid volume. Final drives needed 2 gallons more than the manual calls for. Transmission calls for 74 quarts, only 43 came out though the dipstick shows full. The oil from hydraulics was clean, and pretty. I felt bad changing it. Transmission oil looks like old engine oil; black. It stinks, but I don't think it's a burned smell. The bottom of the transmission has 5 drain plugs. One in center uses 3/4" ratchet to remove. All others need 1". What does this mean. I DON'T HAVE A 1" DRIVE, BUT WILL GET ONE IF IT'S IMPORTANT. The torque converter looks to me to be a twin to my Case 580K converter. The Case backhoe looks to have identical Cummins engine too. Some 580Ks had a drain in the rotating internal portion of the torque converter, later models did not. This old oil is ugly enough I want it fully drained before refilling with new Hy-Tran from Case/IH.

I'm also wondering if I even have a TD7G. I have only a hand cut decal to say it is. The nameplate has no numbers AT ALL!

Dresser TD7G transmission oil

2005 Mustang 2109 Service manual? AND/OR Perkins 1104c-44T service manual?

Hi Guys,

Looking for a service manual (PDF or hard copy) for a 2005 Mustang 2109 Skidsteer. Would also like to see the service manual for the Perkins 1104c-44T turbo motor. Curious about any issues with this engine. I have spoken to a few older guys who claim that this motor has oil sump issues, especially working on grades or leaving the machine idling on steep slopes. Any feedback would be greatly appreciated!

Thanks

2005 Mustang 2109 Service manual? AND/OR Perkins 1104c-44T service manual?

Weirdest or most profitable hooklift beds?????

Thinking about the hooklift business. You always see dump beds, dumpster beds, and flat beds but im looking for something very innovative that nobody around does so i can start out with a leg up on the compition right out of the gate. I already have a very stable business (not hooklift) just looking to add this to the portfolio to be better diversified.

Weirdest or most profitable hooklift beds?????

Double Loading a tilt trailer

Anyone add power to the cushion cylinders of their 20 ton tilt trailers to allow loading of 2 pieces of equipment?

Double Loading a tilt trailer

newbee

Hi all,

Im Al or Alex..Im from the sunny UK and have worked with heavy plant for little over 12 years.I was an operator on a stone quarry working the levers of a SK330 Kobelco, was on that job for 6 years then I got my Dozer ticket and had a blast at being a Dozer op on a semi retired D6N,moved back from the pushing to the digging as work changed and that saw me on a 345 CAT for a good while,worked as a fitter for a hire fleet in gaps in between(Recession).Eventually I got fed up of being out in the cold so I now run an online shop called http://ift.tt/1JQfwJ5 (Construction Machinery paints for those that are interested)

Look forward to getting to know you

cheers Al

Attached Images

  

newbee

Terex Hr 1.6 Stalling Under Load

Whats up guys im having a bit of a problem with my 2006 Terex Hr 1.6 excavator.

At first it started with a tough time starting it then it would finally start and when you would try driving it would immediately stall and when i checked the Diesel 3 cylinder Mitsubishi motor it had turned out to be a crazy loose V belt that was slipping. I tightened that up and it started up great and ran well but now when its under load it bogs down and stalls.

I changed the engine Oil and Filter along with the Air filter and i also did a Radiator Flush and Fresh coolant. The hydraulic oil is Halfway full.

If anyone has any idea as to why its stalling under load i would greatly appreciate any help, ive never worked on excavators before im just a handy home mechanic.

Terex Hr 1.6 Stalling Under Load

99BC 873leaked all gear oil after washing out belly

I am in need of advice where to locate the cause of leak purchased this machine 1/29/16 went straight to carwash and sprayed off exterior and then proceeded to spray the mud out from what i am calling the belly there is an inspection cover off and was spraying in through that access and the water and debris was not draining so with it being on trailer still i had easy access to the drain holes underneath at the rear and i sprayed to clear the hole and then put wand further in to clear out and seconds later it proceeded to leaking all the chain case or gear oil out any ideas

99BC 873leaked all gear oil after washing out belly

deisle engine swap

what engines will interchange in a older massy ferguson backhoe

deisle engine swap

Thomas T15s parts manual or parts????

Looking for manual or a place to buy parts

Thomas T15s parts manual or parts????

Kobelco 200lc controller

I was wondering if anyone could tell me if a computer controller part#2480U411F2. Controls the hydraulics ? On a kobelco 200lc Escavator or if not what does it control I just had some wiring burn up on me and took this unit apart looks like some ICs have burnt

Kobelco 200lc controller

Bob35

540 170 JCB year 2011.steering module replaced back Axel sensor replaced and still not selecting steering modes.front Axel sensor OK.can ya bypass it for four wheel steer or has anyone got a solution.

Bob35

caterpillar d6r series 1 fuel gauge stuck on 3/4s of a tank

do you think its the tank sensor or is it bad at the dash gauge??

caterpillar d6r series 1 fuel gauge stuck on 3/4s of a tank

Thomas T15s

Anyone know where to find a parts manual or where to find parts for a Thomas T15s excavator

Thomas T15s

JCB excavators

Hi gang, new to the site and it seems like a good resource. I am looking to buy a 160 sized machine for farm cleanup, tree and stump removal, ditch cleaning, etc. I was looking at Case, Hitachi, Deere, but came across a JCB much cheaper. Does anyone have experience with these machines? It has the Isuzu engine, which is great, but that's all I know about them. Who built them for JCB? Any input is appreciated. I will probably only put 50 hours/year on it. Thanks

JCB excavators

580L pops out of reverse????

My 580L pops out of reverse sometimes. It doesn't happen all the time but enough to concern me. When it pops out of gear the lever is stays in the reverse position. I can cycle the lever to neutral to reverse once or twice and seems to work fine. Is something electrical failing or or is there maybe some kind of adjustment? Any imput would be helpful. Thank you

580L pops out of reverse????

TRK coupler

I'm looking for a manual coupler for my 200 class excavator. The TRK Multigrab has caught my attention. Do any of you have any experience with this or a similar product?

Thanks

TRK coupler

Pt 75 start fuse

Hey guys I have a Teresa pt 75 almost every day it will blow the start fuse one or more times. But after changing the fuse it works fine most of the day after that. I decided to check it out I have all covers off and skid plates checked wiring from fuse panel right to the start solinode at starter. Don't see any spots where it was pinched or rubbing. Unit is two years old 600 hrs on it I have a wiring diagram and traced the wiring all looks good just hoping someone has had this problem or could help me out thanks.

Pt 75 start fuse

Bucket spoon

Anyone have pictures and steps for attaching a spoon on a excavator bucket without welding it too the teeth. Digging 15" pipe

Bucket spoon

Bob35

I'm at a 540 170 year 2011 JCB teleporter.its stuck in 2 wheel steer.I've replaced the steering control module and the back sponsor.front one is OK.still flashing up on dash code 13 for steering and won't select 4 wheel steer.I no you can bypass this to get 4 wheel steer going but don't no how.any ideas how to bypass or why it won't select steering modes.

Bob35

john deere 7610

i was wondering if anybody might be able to help me please i am trying to get a 7610 going it is a 19speed power shift the trans light stays on it will drive for a couple minutes then stops or if i warm the oil up it then wont go ive changed the filter cleaned the screen it seems to have good oil pressure any tip would be greatly apreiciated thanks wabco

john deere 7610

Ford LTL Single screw?

Anyone ever see one? I am looking at an 86 400big cam and 13 speed

Seems odd to have big engine/trans yet single screw

Ford LTL Single screw?

2005 Caterpillar 308CCR Service/Hour Meter

The hour meter on my cat excavator quit working with only 982 hours on it. It is the analog kind with the red thing in the middle that turns. Does anyone know where to start looking to fix this and what drives these style meters? Thanks

2005 Caterpillar 308CCR Service/Hour Meter

Jd 644 a needs a little sniff

This tractor has what is called a DIESEL STARTING FLUID ADAPTER-----You remove the squirt nozzle and push the can up into the adapter and push the can up while rolling the engine--injecting either into the tractor.

I don't like using ether but this tractor-loader needs a sniff to start even after being plugged in to heat the water. Not sure how warm the water is getting....loader is probably a 1972.

Just looking for some thoughts from the brain trust here--thank you len

Jd 644 a needs a little sniff

Angle cylinder beat up

My TD7G Dresser is new to me. The blade angle cylinders have some scuffing from contact with the inside edge of the tracks. I initially assumed that wear at the pivot points under the tractor explained the contact. Checking, I find little wear in those pins and bushings. My only theory lies in specifications. TD7E has the same tread, but 1" thinner track pads. What causes it? How do I control it?

Angle cylinder beat up

Walking undercarriages

Most very large crawlers have "walking" undercarriages. Maybe I am not using the right terminology. The front crossmember pivots in the center allowing the two track frames to not be parallel. Many small ones do not. Why do I prefer one over another in a 15,000 LB machine.

Willie

Walking undercarriages

Cat 303.5 hydro cooler questions

Hey gang, anyone know where I can pick up a ew hydro oil cooler for a 303.5c for less then the 525.00 I was just quoted? Also any solutions for keeping demo dust out of the cooler and rad? I put a fiber filter on the body and in front which helps but still over heating after an hour when the filter clog.

Cat 303.5 hydro cooler questions

Advice PLEASE

I am looking to purchase a service and owners manual for a Case 550G Long Track. What is the best way to buy it? Download, Paper book? Who would you buy it from? Any dealings with these internet sites that are selling these books? Are all of them the same or is one better then the other?

Just bought a Case 550G today and want to get the service and operators manual so I can read and learn. Thanks for your help

Hogzilla

Advice PLEASE

Case 570lxt not moving?

So I changed the hydraulic fluid on my Case 570lxt, and fixed some leaks it had. But now it won't move forward or reverse.
It was working good before I did anything. It turns on great, and the bucket lifts but when I try moving it it doesn't move.
It makes a grinding type noise when i go to move it, and also kind of wants to engage but it doesn't. What do you think could be
the problem? Does my hydraulic change have anything to do with it? Or could it be some electrical problem? All help is appreciated thanks.

Case 570lxt not moving?

Plasma cutter?

I have a cattle truck with 5mm chequer plate floor that needs replacing.
It is welded, underneath, to rhs cross members.
I'ld like to blow those welds off without removing the tray, if possible, but access is very tight in spots.
Never used a plasma before, but thinking it might be an option.
Doesn't matter if we make a mess of the floor, it is rooted anyway.
Thoughts?

Attached Images

  

Plasma cutter?

Komatsu PC200LC-6

Hello everyone, I'm new to this forum and I would like to ask if any of you would know why a Komatsu 200-6 would still have starting problems after I had the starter, starter sol, and secondary sol replaced?

Komatsu PC200LC-6

D6H Hard nose loose

I'm looking at a 6H to buy and the hard nose moves back and forth when you lift and lower the blade. now I did research the replacement pins and in doing so discovered there is also bearings in the bors. So i'm wondering what my chances are that i could get away with just replacing the wear parts or if i would have to do some line boring.

The other issue is the hard bar. I know for sure that the end bearings are out but not sure if its eat into the bar its self. Not sure where to look for after market. I do remember seeing a thread on here some time ago where a guy had a simillar problem and he got an after market on for under 2k i think (5685.00 from CAT). I have a price on parts from cat for everything for the hard nose to the hard bar (including the bar itself) $7536.00
I have yet to get oil samples.
Is there any other problems that the older H"s are proned to?

ser# 4RC01861

D6H Hard nose loose

D6r sprocket bolts

What is the torque spec on the sprocket bolts on a d6r ii?

D6r sprocket bolts

LS180 smoking

I have a 2000 LS180 skid steer and it recently starting smoking (white smoke) badly, running rough and losing power badly. It also is using anti-freeze. No leaks,. Anybody have any suggestions? I'm thinking maybe a head gasket? If the machine sits for a while it's runs fine at first and the longer you run it the worst it gets? Oil level is ok.

LS180 smoking

How does this scraper unload?

Can someone tell me how this scraper unloads? I think it is an International Harvester. I don't see the sheeves in back to push out the front. What model?

Attached Images

  

How does this scraper unload?

Does D10T Ripper also fits on D10R and D10N machine?

Hi,

Does anyone know if D10T Ripper fits on D10R and D10N machine?

Thanks.

Does D10T Ripper also fits on D10R and D10N machine?

G188 flyweel throw oil In starter

Hi everyone, m' pretty impress about all good info we Can find In this forum . Very helpfull!

I have a 1971 case 480B loader/backoe . Just had to flush and replace the 7.6 l shuttle oil this week cause there was too much water In it and was freezing.
I also had some starter prob. It took lots of key stroke before it would engage. So removed and clean the selenoïd which i found was all soiled with that old watered shuttle oil.
Can someone tell me if it' s normal to find shuttle oil In flyweel compartment? Result is that it throws it In starter selenoïd as there is a passage In bendix fork mechanism that is not sealed ?

Thank you much!

G188 flyweel throw oil In starter

Cat d5h transmission problem

Hi anyone ! I have been struggling with this cat d5h transmission. The machine works very well while the temp is still cold. As soon as the transmission temp gets to normal or above, it won't select 1st gear. 2nd and 3rd works fine. It has damaged the 1st gear ring seal 3 times now that have been replaced. I have replaced the transmission pump, overhauled all valves and brakes. What else can i look for? Any help will be very appreciated. Henk

Cat d5h transmission problem

Looking for a Ford 555C backhoe door

I'm looking for the drivers side door frame anyone know where I can go to find one?
Thanks

Looking for a Ford 555C backhoe door

Please help, about the D6T VPAT blade and SU blade

Hi everyone,

I have a D6T SU blade, if I change it to a VPAT blade, can I use the previous lifting cylinders? Are they the same?

And also I see some many different VPAT blades in different part number: 3341804 (2 types), 3341805 (2 types), 3341809 (3 types), 3878449 (2 types)

They all share some of the same parts but some are different. Do they all fit on D6T machine? Anyone knows what is the difference?

Thank you so much

Please help, about the D6T VPAT blade and SU blade

2007 Genie S60 Engine won't turn off

I have a Genie S60 serial number 16590 with a Deutz D2011L03i. The lift starts and everything functions ok. When you try to turn it off it won't die. The Emergency kill buttons and the key have no effect. Anyone have this problem?

2007 Genie S60 Engine won't turn off

Found a D7G dozer with 30 hours

Found the D7G Serial number 3FG000058 and states it only has 30 hours on it (US Navy). That said if this is correct what do you think would be the issues with something like this sitting for that many years?

Found a D7G dozer with 30 hours

Case 450d

I have a case 450d and can not find the transmission drain plug. I removed the rear belly pan under the tranny and removed a large bolt at the lowest part of tranny but only about a quart of fluid drained out. What am I missing

Case 450d

LP Forklift

Anyone know if they make an adapter to run a LP forklift off a 20 pound gas grill cylinder?
Have been looking at some upcoming auctions and while the machines run some don't have cylinders. Figured I would buy the right cylinder if needed but if it came with one then wouldn't bother. Just need a way to start it up and get it on and off the trailer

LP Forklift

Case 1825 charge pressure alarm

Hello, looking for some experience here. We have a Case 1825 w/gas motor. The Charge pressure light/alarm is staying on much longer than normal when cold starting the unit. Once it warms long enough (several minutes) to go off and drive is active it runs fine. The normal warm time even in cold weather 0-20 deg F, is usually only a minute or two. If you move it too soon it will lock the drive for several minutes. We've had it for several years, doesn't see heavy use and seems to only act this way in cold weather. Thanks in advance for any help.

Rick

Case 1825 charge pressure alarm

Forks for my JD544

Hello

Looking for advice from experience, I have a 544 with a bucket, I have JRB long forks, I am also looking for short forks, I will be using to move junk cars, would like the flexibility to pickup lengthwise and from the side, Will eventually upgrade to an l70 or similar but have this to work with for now. what do you think is my best option to start moving my cars around???

Sorry if my write up seems cut and dry but my 1st attempt just got deleted by accident so I removed all the fluff.

Thanks for the help!!!

-Alex

Attached Images

   

Forks for my JD544

hough 65c torque convertor problem or not?

your help is needed, our pay loader is having problems moving, its is very sluggish ,once it is moving it is fine , if you try to drive into a pile of dirt it just stops ,the engine keeps going but the loader just inches forward.how would i tell if it is the torque convertor or pump ? it seems to lift ok. strangely when you put a new battery in it it runs better (it has a charging problem)let me know what info is needed.
thanks

hough 65c torque convertor problem or not?

Turn your EGR valve off on your series 60 Detroit or Cummins ISX Turn your EGR valve

Turn your EGR valve off on your series 60 Detroit or Cummins ISX, model years 2004-2007. No engine lights. Better Power, throttle response and fuel mileage! Plug and play device. Also offering ECM tuning and products for Caterpillar engines.

Go To http://ift.tt/207vqWC

Turn your EGR valve off on your series 60 Detroit or Cummins ISX Turn your EGR valve

Turn your EGR valve off on your series 60 Detroit or Cummins ISX

Turn your EGR valve off on your series 60 Detroit or Cummins ISX, model years 2004-2007. No engine lights. Better Power, throttle response and fuel mileage! Plug and play device. Also offering ECM tuning and products for Caterpillar engines.

Go To http://ift.tt/207vqWC

Turn your EGR valve off on your series 60 Detroit or Cummins ISX

Turn your EGR valve off on your series 60 Detroit or Cummins ISX

Turn your EGR valve off on your series 60 Detroit or Cummins ISX, model years 2004-2007. No engine lights. Better Power, throttle response and fuel mileage! Plug and play device. Also offering ECM tuning and products for Caterpillar engines.

Go To http://ift.tt/207vqWC

Turn your EGR valve off on your series 60 Detroit or Cummins ISX

Turn your EGR valve off on your series 60 Detroit or Cummins ISX

Turn your EGR valve off on your series 60 Detroit or Cummins ISX, model years 2004-2007. No engine lights. Better Power, throttle response and fuel mileage! Plug and play device. Also offering ECM tuning and products for Caterpillar engines.

Go To http://ift.tt/207vqWC

Turn your EGR valve off on your series 60 Detroit or Cummins ISX

CAT M315 excavator diagnostic software & hardware needed

Hello,

Company I work for is going to buy some used M315 & 312 excavator. Can anyone tell me what hardware and software I must have for doing general diagnostics to those vehicles with pc?
Actually I have a licenced Electronic Technician 2015 and a communication adapter 3 which I use for wheel loader diagnostics. Are these enough for the excavator M315?



Thank you in advance

CAT M315 excavator diagnostic software & hardware needed

L70 Intermitant brake failure

Hi all

My L70 occasionally has 100% brake failure. It's not front or rear but the complete circuit.


The gauge drops to zero


My older Volvo loader has a compressor but this one doesn't seem to have one.

Looking through manual it appears to be this that powers the braking circuit.


Does anyone have any idea what the problem could be?

Cheers

Attached Images

   

L70 Intermitant brake failure

Cat 262B ignition switch or relay not working

Hopped in the Cat this morn and got flickering dash lights on key turn...then nothing! Cleaned all batt points and chased/checked wiring..still wont kick. Batt good.
Dash flickers when key moved slightly so im guessing the ignition is broke? Or startup relay? Anyone got a diagram to look at???
cheers in advance.

Cat 262B ignition switch or relay not working

Can a Case 188 block be a donor for a cracked 207 block?

First time poster, but I have checked the forum search here for previous threads on this subject. I found a few but they all were kinda short on specifics.

I have a 1978 Case 580C backhoe that I just bought (got it for relatively cheap) and the block is shot.
It has the 207D non turbo engine. Engine Serial no 2850509
Pulled the sleeves and the block is cracked between all four cylinders. Water froze.
The engine has low hrs (2700) and everything else specs out. I checked the crank and it is on the high side of standard. Same with valvetrain,..almost zero wear. Head is in great shape, as well as everything else on the backhoe itself. It's a shame this block is shot because everything else is in outstanding shape. What to do?

I have had no luck finding a 207 block or even a core engine. I have found a few 188 engines and have heard that the "blocks are the same" But I need to be convinced before I dump money into a 188 donor core motor.

I see where the 188 and the 207 have the same stroke, but different bores. When they went from the smaller bore on the 188 to the larger bore on the 207 did they achieve this by just making the wet sleeves thinner? Or did they change the actual bore of the block that the wet sleeves went into?
(Want to know if my 207 sleeves, pistons, and rods will fit in there)

I've also heard that some of the 188 blocks had different widths on the lips of the wet sleeves on top.
If so,...which 188 type should I be looking for to allow me to use my 207 sleeves?

Reason I want to know is that what I'd like to do is buy the 188 and just use the block,...and swap all the 207 intermals over to that block. I know the rod journals are different on the 188 but if I swap the crank,....that shouldn't matter right?

The guy about 2 hrs North of me has a few 188's to choose from,...is there one specific type (year, etc.) in particular to look for or even ones to specifically NOT choose. ?

Basically, I want to know,...for 100% sure,...that if I had a bare, completely stripped 188 block, can it be used to put all my 207 stuff in without issues?

Thanks in advance for helping me out with this. I am hoping to get this machine together soon so I can put it to work on my new homestead. Have lots of projects in mind.....

Can a Case 188 block be a donor for a cracked 207 block?

Zaxus 225 Tech Manual

Does any one out there have the tech. manual and workshop manual for a ZX225USRLCK-3 , Product ID# HCML1U600J00207988 . Would be handy for some trouble shooting and repair. Thanks in advance for your help. Simon

Zaxus 225 Tech Manual

Olympic Cattle

Was out by Lake Ozette this week came across these in a pasture along side the road. Was wondering if they raise them for meat or milk. I suppose that's how those loggers out there got so ornery and tough.

Attached Images

   

Olympic Cattle

ed

Can anyone tell me where the hydraulic filter is located on a case 580 super K?

ed

D5g help!!!

I have a cat d5g that is givin me some problems i cnt figure out any help wld b great..it starts up fine but when u idle ur hand throttle dwn to about 1000 rpms it will run a second and die. I just put new throttle cables on it and tried adjusting it out there but no luck. Im needin some advice on things to check plz???

D5g help!!!

Cummmins 6BTA 5.9 c

Hi there guys, anyone got a parts list or link to same for serial no. 21600032 engine fitted to a T & L Irrigator.

The list supplied is way out of date and the injection lines are not correct for ours.

Thanks Gregg.

Cummmins 6BTA 5.9 c

Cat 277C yellow exclamation warning and beeper.

Hi Guys, I'm a newbie here from the other side of the World but I'm having an issue that needs some outside expertise. I have a 277C with only 200 hours on it, but it is three or four years old. Last week it started showing a yellow exclamation warning on the left side top panel. I don't have the top right panel so no way to read codes. If the yellow light was on it would steer slightly to the left in the straight ahead position and you have to keep pushing it back. Really annoying.

In desperation I purchased a CAT ET system and it has a code E568 and says left drive motor speed sensor #1: Erratic, Intermittent or Incorrect Then another one that says Left Drive Speed Sensor #1: Abnormal Frequency, Pulse Width or Period?

Any clues as to what this could be?

I've followed the wiring where it exits the lower side of the cabin and attaches to the hydraulic lines. There is a plug there and I removed and cleaned that but it was clean as can be inside. Very well sealed. There isn't any physical damage to the wiring that I can see. You can trace with your fingers and a mirror and see that the wires go into the back of a silver steel housing which is probably the speed sensor itself.

Could loose tracks make one side go faster than the other and upset the ECM? I've only recently purchased the machine and done less than 20 hrs on it but I don't think it's even had it's first service let alone had the tracks adjusted ever.

At first the light and beeper came up and stayed on until forward motion stopped and hand was off joystick. Then after a while it actually stopped the machine, no forward or backward motion just the bucket still operating fine. Turn off the machine and do a full restart and it came back again.

Back to the shed with it, checked filters, air intakes, levels etc, topped up the hydraulics which were 8 liters down and cleaned the pre air filter which was nearly clogged with fine dust and I was sure that this would fix it but the next time it went out it repeated the same fault.

Here's a picture of the screen dump created by the CAT ET.

Attached Images

 

Cat 277C yellow exclamation warning and beeper.

Zinc-free Hydraulic

(I know there's a thread around here somewhere but couldn't find it.)

My question is, is there anything wrong using zinc-free for older machines that don't require it?

I only have one bulk tank so it has the zinc-free

Zinc-free Hydraulic

2006 Link Belt 330LX excavator for sale

2006 Link Belt 330LX excavator, runs great, A/C and heat, thumb, new bucket teeth, all oils and filters changed less than 100 hours ago. 8678 hours. Can arrange delivery. Trades considered (dozer, CTL or backhoe) or make an offer. Call, text, or email. If it is still listed, it is available.
Contact info: 4237742813 or sdcochrum@aol.com

Attached Images

     

2006 Link Belt 330LX excavator for sale

OM421.905 V6 Engine - USA?

"OM421.905 V6 Engine but you will need to figure out locally what items use such engines in the USA"

Hello ALL does anyone know what American machine/vehicle uses this type of engine/motor? Any help is greatly appreciated, as I cant seem to get anywhere on my own.

OM421.905 V6 Engine - USA?

ground protection matts any one using them?

Im a pool builder and general excavator and im looking in too getting some ground protection mats too mainly to use on the pool side im looking at them to help with getting dump trucks in too backyards when it muddy or soft out but not sure if there worth the money. http://ift.tt/1NBAtlF this is a link to the ones im looking at figure im going to spend almost 6k on them to get 150 feet off the road just wondering if any one has any experience with them or any other brand, are they worth the money, will the really help any?

ground protection matts any one using them?

kill switch

My 2001 volvo ec210lc cummings engine kill switch not working I have replaced it still doesn't work any suggestions
tia

kill switch

New Tires for my Tractor

My rears on my tractor are worn and thin. Current size is a 420/70/24 R4 tire on a 15" wide wheel. This tire has become a bear to find and when found is Butt _ _ _ Expensive... to the tune of about $862 each, not counting tax and shipping.

That said, this is a 4wd tractor running 10-16.5 R4 tires up front. Would there be an issue moving the rears up to 17.5x24 R4 tires?

I have a conversation going on another site about this, but I brought it here because I have noticed that a John Deere 110 TLB (2000-2012 models) run the 10-16.5/420.70.24 tire combination and it is a 4wd chassis tractor.

If it works for one manufacturer, would it work for another, or would gearing be different thereby changing the drive line rotation ratios?

Current machine information
Kubota L2950 DT GST 4WD with Loader
Rear tires - 420/70/24 R4 - (47.1" tall with Rolling Circumference of 148")
Front tires - 10-16.5 Skid Steer Tires -- (30.78" tall with Rolling Circumference of 96.69")

Proposed 17.5x24 Rear Tires - (48" tall with Rolling Circumference of 150.75")

I just want to make sure that I am not putting undue stress and binding on the 4wd drive line by mismatching the tire sizes on this machine.

New Tires for my Tractor

anyone has repair manual and possible parts manual for volvo ec140b lc excavator?

I am running into some problem with my excavator and need the manuals to troubleshoot and find possible parts. I am new here and will help you guys out in the future. :cool2

anyone has repair manual and possible parts manual for volvo ec140b lc excavator?

Fiat Allis 10C Dozer

Can anyone tell me the good and bad of the 10C dozer and if you can still get undercarriage parts and if so where?

Attached Images

 

Fiat Allis 10C Dozer

Manifold

Gentlemen

I would be interested to know if one of my fellow forumers here may know where I can find a good used exhaust manifold for a 580D Turbo, Case PN A155123. It is not my desire to turn this site into a commercial site but I would like to reach as large a group as possible and this is by far the best place.

If any info post back here and we will PM with details.

Thank You, Mel

Manifold

Opinions: D41P-6

I'm looking for a 6-way dozer to add to my fleet. I've ran JD 450G & a D31P and while they did what I expected, I'm looking for a larger machine. I already have a 45,000# straight dozer for the bulk pushing and I need a clean-up and grading machine. I don't really have space restraints as I don't do much residential hence the reason for a slightly larger rig. I already have a lowboy so no hauling issues, and a couple skid steers for the little stuff.

I only expect to put about 200 hrs/yr on this one so it's more of a support machine. Still better than hauling both a big dozer and a tractor or skid steer for the small jobs.

What can you tell me specifically about the D41 and any other suggestions on a similar sized dozer.

Opinions: D41P-6

Apt building weight per square foot

Bidding a apt building demo, 2 story, 24 unit with full basement, brick exterior. Looking for a rough estimate on a weight per square foot.

Apt building weight per square foot

NOOB: Gravel Parking Lot

Been reading this forum and watching dozer vids like crazy for days now...for hours at a time. I will continue to do so moving forward. Great info.
I have a small bar in Houston with a small asphalt parking area and a large grassy area that's mostly flat but too bumpy for cars. I've been getting busy lately and need more parking because vehicles are getting stuck in certain spots.
It rains too often and the grassy area isn't compacted. I got quotes and just couldn't afford it.:Pointhead
I have to do this myself due to finances. I have operated skids, tractors and such but never a dozer. I have a customer & experienced uncle who will operate the dozer for free if I rent one. My uncle lives about 4 hours away & it keeps raining during the time he's off work to come and do it.
It's a little less than an acre of grassy land. I used a loader (needed a dozer) to spread about 30 loads of dirt and the grade is all wrong and not compacted.
When I got quotes they said they'd level, compact, spread the gravel and compact the gravel. This is what I want to do. I'm going to install 4" of gravel on it for now and come back and put another 4" later. I'm trying to do as much as I can with what I have to work with.
My uncle said rent a dozer for him so I was going to get a Case 550 or similar from Aztec and a sheepfoot roller (idk what size). I'm buying the gravel directly from the yard, Southern Crushed Concrete, with delivery. It's raining now. If it's not too sloppy, and he's off work, he'll come do it and I'm fine. If not, I have to utilize my customer, myself or just postpone it all.
I have a huge Super Bowl Party coming and they're planning to tailgate in that area but it's too muddy and they're worried. I am as well so I'm trying to get something done. If you guys can offer advice I'd sure take it. And appreciate it. I WANT to jump on that dozer and scrape, grade and compact it myself since the area is relatively small figuring I could 'fix' the mess ups. So that's why I'm asking for your advice and expertise. Thanks.

NOOB: Gravel Parking Lot

international 4700 trans swap

alright guys this has been a month so far trying to find a few parts.
so whats going on is we have a 1998 international 4700 with the t444e with a 5 speed, we pulled the 5 speed and the boss bought a fs6106a which is 1 of the trans offered in this truck, what im trying to find is the bracket for the back of the fs6106a that the driveline brake bolts to it also holds the rear seal, i have been dealing with motor truck but have been getting no where really, any help would be appreciated

international 4700 trans swap

1953 d8 cat value?

I acquired a 1953 cat d8 that will soon be for sale. It has a cab and roll bars, the under carriage looks good and it runs and operates as it should. What should i be asking for it?

1953 d8 cat value?

Case 580 super e boom dropping down!

Hi, i have an '80s model case 580 super e 4x4 extendahoe, recently the rear boom started falling to the ground! My dad was loading logs with the rear boom, and it got so bad he couldn't keep it up, as soon as he let off the leaver, it dropped to the ground. There are no external xylinder leaks, is there anything i can check or does anyone have any idea as to what is going on?

Case 580 super e boom dropping down!

CDL DOT physical exam

I am not quite sure if I am in the right forum or website but, any insight is appreciated.


Cardio inhibitory syncope and CDL license/DOT medical exam.?
About 3 years ago, someone that I know fainted suddenly while seated in a barber chair. In following up at the doc's office, a tilt test was done. They fainted and heart stopped for about 13 seconds before the doc stepped in. From that, they were diagnosed with cardio inhibitory syncope. Meds were given but, never taken. There had been no fainting issues before then and none since.

This person is now interested in becoming a OTR driver and training for their CDL license. We read somewhere that fainting/apnea type issues were a no-go when it comes to passing the exam. In discussing this with the person, they don't plan to mention the syncope or episodes to the examiner because they feel it was just a 1-time happening. Won't old medical records somehow reveal this at the time of testing? T

CDL DOT physical exam

Bobcat 763 needs tires....

So I am looking into tires for my machine and the question is to foam fill or not? I got the machine and the tires ar foamed and I am wondering how hard to retire now and if I should foam again.
Weight- foam is heavy.....machine sees all around work on all surfaces

Bobcat 763 needs tires....

Battery or alternator issue?

So I have a bobcat 763 with 2600hours. Battery is a year old has sat for weeks then started right up. Used everyday for past 3 days without issues. It sat all day and when I went to start it this evening and it was dead as dead can be -- nothing. I jumped it after a few minutes and it showed 3/4 on the gauge..... Fluke? Or do I have a problem brewing? Will check status tomorrow night......

Battery or alternator issue?

Mustang 2040 keeps stalling

Hello, my Mustang 2040 skid steer will randomly stall. It will start up and run with no problem till it happens again. There doesn't appear to be any pattern to it.
I am thinking it is a faulty engine protection device (low oil, high temp etc) but the engine is not hot and has all of its fluids.
Does anyone know exactly what devices are fitted that could cause this? If i can get a list i will work thru them to find the culprit.
Thankyou, Paul

Mustang 2040 keeps stalling

941 Steering Clutch Adjustments

On my recently acquired 941 Ser # 80H 298X (cannot read the last number) I ordered & received a parts book on Ebay that covers that Ser # but this parts book covers lever steer not pedal steer like mine. I was wanting to ask if anyone may have a page or two that shows the linkage & mechanism inside of the steering clutch compartment. I believe there may be a roller assembly just inside of the case on the end of the linkage & I wanted to get a better understanding of what the breakdown is like, if anyone could help me. This machine has wet clutches & brakes & is power shift. My problem is the clutches are not releasing properly, before the brakes begin to apply.

Attached Images

 

941 Steering Clutch Adjustments

08' 6x20 Screen and 08' 36x125 Powerstacker FSBO

Looking to sell our 6x20 Cedarrapids 3 Deck Screen as well as our Superior 36x125 Powerstacker.

Both machines are ready to work, and in excellent shape. Pictures available upon request.

Machines are located in Northern MN.

08' 6x20 Screen and 08' 36x125 Powerstacker FSBO

Case W11 torque convertor

Looking for a source to purchase a remanufactured torque convertor and flex plate . Nothing available on the east coast I can locate . I have all the tags to identify and there were two different transmissions in 1984 .

Appreciate the help .

Case W11 torque convertor

Hitachi EX120 swing bearing bolts

I am working on a Hitachi ex120, and found there to be 8 bolts missing from the underside of the swing bearing. There is 6 missing underneath the cab, and another two directly opposite on the other side of the machine. I haven't been able to find any information, except in an older post on this forum that said there should be 30 in total, and in a catalog that says it ships them in packs of 36. There's nothing at all in the manual, and only 28 on the machine I'm working on. at first I assumed that they had broken off, but when I look at the top side of the bearing, all the bolts that are still in poke out the top about 5mm. Where there are studs missing, there's nothing poking out, and no hole where a stud would come through.

I'm doing this as part of my foundation heavy duty course, so I'm not sure if I just don't know my ****, or what. I'm basically convinced that they're supposed to be empty holes.

anybody know what the hell the deal with these is? thanks.

Hitachi EX120 swing bearing bolts

Daewoo excavator s 170-111 piping trouble

been having major issues with this machine!

previously hydraulic been overheating and had a worn out main pump, just replaced with a new pump hoping it would cure overheating but it hasnt.

machine has alot of power now!

control valve was leaking alot so got that out and replaced all the Orings around it. unfortunately putting it back in with all the oil everywhere i lost a few of my pipe marking but managed to get it back on, done all pressures, main relief@ 320 bar and overload@ 340, swing @ 250.

now having an issue when i use boom up or down it releases the swing brake and feels like the engine slighty loads! ive got some pipes wrong somewhere, would be really great if someone would help me with some piping pictures?

plus the hydraulic overheating issue!

cheers guys

Daewoo excavator s 170-111 piping trouble

Case 580L bucket cylinder

any recommendation on where to buy a used/rebuilt OEM Case bucket cylinder for my 580L
I am located in the northeast, Thank you

Case 580L bucket cylinder

CAT 955K wont ramp up and looks to be spraying oil from oil pan/engine gasket

I recently got my 955K stuck. I drove it back to the house, about 150 yards, and everything was running fine. I have had it idling for a few minutes while I moved to loader around to get a linkage pin lined up so I could put it back in. 2 days ago, I started it up and it would not throttle up. I got off to check the throttle linkage and noticed a couple of fine streams of oil coming from what looked to be the oil pan and engine interface. I shut it down immediately as I also noticed some knocking coming from the engine. The oil was coming from the front right of the oil pan. Is it possible that something has clogged the oil lines and backed up enough to pressurize the oil pan? Any ideas? I am going to remove the filter this evening to check for debris and to check the bypass on top of the filter housing. I am not very familiar with these machines so any response will not insult my intelligence.

CAT 955K wont ramp up and looks to be spraying oil from oil pan/engine gasket

John Deere 210C

Hi.

I have an 89 Deere 210C. It requires a new backhoe bucket. I have found a replacement, but it comes with 2.5" pins. I know mine takes a 1.5" and a 1.75". What Loader backhoe buckets come with 2.5" pins? Its a great price, 24" and will fit my machine, I will just need to get some bushings machined and hardened.

John Deere 210C

Winter dozing

I have a little 10 acre patch of trees to take down for a customer. Mostly poplar. 8"-12" diameter trees for the most part. I tipped them all over about 10 days ago then let the ground freeze-up a little. We had some-25*F nights so I figured it would be hard as heck but I still have to be careful to not roll up dirt with the trees. We will start with a heavy disk this summer and burn the windrows as they dry. My D65 is a bit small for this type of work but It gets done. OROPS are cold.

This method seems to give the cleanest finished product with the least amount of dirt in the piles. How do you other northern folk prefer to clear land?

The pics are poor but we all like to look.



Same spot from the other direction after windrowing.

Attached Images

  

Winter dozing

977h engine performance problem

Hi
This 977 I have is being a problem, it has a d333 engine and runs smooth until revs are increased above about 1/2 throttle. I have been through the fuel system, replaced filter, cleaned out primary bowl and gauze, removed air filter, replaced injector nozzles, even tried fitting a high pressure electric fuel pump and also checking the turbo bearings, but the engine still is breaking down under high fuel demand situations. Running out of ideas. Running out of patience. If anyone can help that would be great.

977h engine performance problem

machines brand drott

prejudice if it were possible I would like to have information on the machines and excavators brand drott believe are the ancestors of houses, especially wheel excavator drott 80 cruz air, I believe you call it, from what I know has drott inbentato bucket multi function one in four , I am wrong?

https://youtu.be/3GIU0L-Ks8M
https://youtu.be/Mdbb5EahZvM


:confused:

Attached Images

    

machines brand drott