"Back in the Day"

...

"Back in the Day"

"Back in the Day"

Pacific trucks in the logging industy

Post pictures of Pacific trucks in the logging industry.:canada I thought I better close the gap/ring of huge logging trucks so all makes are represented. Here are some LLL P16 models at Port McNeill.

Pacific trucks in the logging industy

Hitachi EX135UR-5 won't throttle up

I have a 2002 hitachi ex135ur-5 that won't throttle up. Worked fine then sat for a couple weeks and the problem started. The key will start the machine but has no effect from the on. It will only idle and they key will not shut it off. I have to use the manual emergency stop cable.
I have another identical machine that does run so I've been switching parts but no luck. I have checked all the fuses, switched relays around, changed the computer, the step motor, the alternator, the key...

Hitachi EX135UR-5 won't throttle up

Hitachi EX135UR-5 won't throttle up

takeuchi final drive oil? sae 90 equivalent?

last time i changed the final drive oil on my tl140, i believe i used 75w-90 gl5 mobil synthetic. when i went to drain this time, the old oil came out dark and very frothy and aerated. not milky or anything like that. just lot of small air bubbles.
the manual callls for sae 90 gl4 oil, which is hard to find. this time i put in valvoline 80w-90 gl5 gear oil. will that be ok?
the one thing i read online is that the newer gl5 gear oils can cause wear on yellow metals like bronze or brass....

takeuchi final drive oil? sae 90 equivalent?

takeuchi final drive oil? sae 90 equivalent?

Terex TS14B blower

Hey everyone! Just got a TS14b from an auction. Had some old Euclid S18s with 6110bs in them but never a little 471. The back engine won't shut off with the blower. You flip the lever and I can hear it close and motor slows down but chugs black smoke. It runs at a very low idle. Had to loosen fuel lines to get it off. Any ideas? Could it be a gasket in the box? Or do I need to go into it?

Terex TS14B blower

Zacklift

I have been looking at putting together a tow unit for the trucking company I work for. And I think the
best way to go is build a truck with a Z353 Zacklift with 25,000 lb stiff legs and a 30,000 lb drag winch.
Looking at a 2000 379 Pete with a 450 hp Series 60 and 10spd with 3:55's. I will stretch it to 300 WB.
And just install some tool boxes and tandem fenders. Sort of like this one. But it will be a permanent
mounted lift.

Truck Shop

View attachment 167483

Zacklift

D6N LGP vs XL

Looking for some input from anyone with experience with these tractors D6N LGP or D6N XL? . Quite a bit of difference in the two machines when it comes to the blade. LGP has the 13.4 wide blade and sets out from the tractor quite a bit more for the longer tracks than the XLs 10.7 wide blade. I do farm work mostly clearing -ditch work- building pads -ponds exc. Needing a dozer that will work well with a 320 excavator.

D6N LGP vs XL

the old 580B Question

I have a question on the 580b case, The enine is a 188 and has the im thinking power shuttle, well the starter has a little bolt on the housing between the starter sylinoid, and starter motor, this bolt keeps leaking fluid around it, is this an adjustment bolt? can it be removed and an o-ring put on it to keep it from leaking? I guess a pic would help also ill try to get one


Thanks Mike

the old 580B Question

25-30 year old trucks, why one over another?

I'm hoping to gain some knowledge/insight about this vintage of trucks from the guys who drove them. I didn't grow up around trucking, or the truck industry. All of my experience has come from the dairy farm where we haul grain, forage and have a dump truck for farm related projects. I've logged quite a few hours in Ford Louisville's and recently some hours in a Mack CH600. I find the Mack quite enjoyable as I am a taller person and it just has more leg space in the cab than the...

25-30 year old trucks, why one over another?

25-30 year old trucks, why one over another?

AC 645 fuel pump challenge

I need some assistance. Have a former military loader and it just does not want to run right. We have books and have tried various approaches but it seems to be temperamental.

Runs strong but once the RPMs get down, it wants to die.

AC 645 fuel pump challenge

Detroit 2-Cycles in 2017+

Junkyard's post on the winch trucks had me wondering about how much longer these antiques are going to be supported. Well lo and behold I found this:

http://ift.tt/2i0GUub

According to that, they are still building new 53, 71 and 92 series for the military.

What kind of machines are they going into? What level of computerization? What level of emissions?

At least it is encouraging that they are...

Detroit 2-Cycles in 2017+

Detroit 2-Cycles in 2017+

KOMATSU HM300-2

Have a machine im dealing with at the moment. Its a HM300-2

Symptom: machine operates in forward & reverse, shifts through gears as it should, but as soon as I disengage the "inter-axle diff lock" (turn the switch to the off position), the machine jars up and will no longer move.

Selecting gears plays no bearing on the issue. No active codes present. Monitor sees no abnormalities as far as control pressures, fill switch errors, diff lock prop. solenoid...

KOMATSU HM300-2

KOMATSU HM300-2

I got a 955K 61H622

I'm missing my dip stick to my hydraulic fluid tank opposite the diesel tank. I'm trying to make me a dip stick for measuring my hydraulic fluid level. Can anyone take measurement on their stick. Thank You

I got a 955K 61H622

Saying goodbye to an old friend

Today I said goodbye to an old friend, my D4D which I have owned for a few years now. I hardly used it anymore & a man over 1,350 miles away saw it advertised & ended up buying it. I have mixed feeling about parting with her, but due to the fact I hardly had a reason to own it, I decided it may be better for someone to own it that could put it to better use. The man that bought it has some brush rows to take out. To get a good shipping rate, it needed to be loaded onto a step deck. We...

Saying goodbye to an old friend

Saying goodbye to an old friend

Looking for some advice on demo job.

looking for some advice on a 30x50 two story house. Block foundation with a 8x20 attached porch with roof. I'm needing help figuring my tons. Will be hauling in tandem dump trucks. 16' boxes. Be my first house demo. 2x8 floor Joice 2x4 frame, paneling on the wall. House is empty besides cabinets and carpet. Any advice I would sure appreciate! Thanks in advance.

Looking for some advice on demo job.

John Deere 300D Series II ART

S# 650588

Looking for a complete wiring schematic and list of fault code definitions. Any help would be greatly appreciated!

John Deere 300D Series II ART

Case 580L series II service manual

Anybody have one they would sell, copy, pdf to me etc... I really need one and cant order it from the dealer and i have been looking for 6 months with no luck yet. Any help would be appreciated.

Case 580L series II service manual

AFE mulching head

Hello all. I'm new to this forum but I've already found a lot of very useful information on it! I am thinking of adding a mulcher to my lineup of attachments and as a custom fencer Central British Columbia I have got a lot of trees to deal with! I have been wondering if anyone here has run one of these AFE disc type mulchers and if so what was your thoughts on them? The size of the mulch isn't my greatest concern because it will break down fairly quick in our climate, I just want to be able...

AFE mulching head

AFE mulching head

KOMATSU D20S STARTER PROBLEMS

I would love some insight as to what my problem is. I just replaced the starter on my loader. My loader is D20S-5 Model 50540. I had to replace the starter because a wire came off of the relay on the old starter. After I replaced the starter I tried to start it and I am getting nothing. Not a click, not a slow start... nothing. I jumped the starter yesterday to make sure the starter was good and it started right up by jumping. After I got it started I shut it back off but I noticed the...

KOMATSU D20S STARTER PROBLEMS

KOMATSU D20S STARTER PROBLEMS

TAKEUCHI TL12V2 owners ?

Does anyone own 1 of the new TAKEUCHI TL12V2 at all ?

Cheers

TAKEUCHI TL12V2 owners ?

Model Modifiers

Does anyone have a link to a list of what different modifiers mean? Example 345DLVG or 330CL.

Model Modifiers

Used Surplus Proto Service Wrenches

I'd like to preface this by saying I'm am not affiliated in any way with the company, I just figured I'd share these in case anybody was looking for a reasonable buy on them, and they're relating to equipment repair. If this doesn't belong mods, please delete away.

I bought a set myself of the 24 sizes they had. I used the new customer promo code "WELCOME2USRO" for 20% off. With free freight, the bill was $280....

Used Surplus Proto Service Wrenches

Used Surplus Proto Service Wrenches

Detroit 6V92 exhaust riser pipes

We've got a 1985 Ford 9000 with a DD 6V92. The exhaust riser pipes on both sides have cracked at the flanges. These connect the manifolds to the turbo base. The left side pipe cracked at the top flange, the right pipe cracked at the bottom manifold flange. Both pipes cracked in the last couple days while we were chopping hay. We brazed them last night, but we're not overly confident about brazing being a long term fix for them

We called our local Detroit dealer and they said it's $800...

Detroit 6V92 exhaust riser pipes

Detroit 6V92 exhaust riser pipes

3/8" to 1/2" hyd. hose OK?

I had a 3/8" swing cylinder hose bust so I got replacements for both of the lines as both had friction wear....

They did not have 3/8" hose so I went with 1/2". It is working well but now I have a leak on one of the swing cylinder seals. Could that larger hose be putting more pressure on the cylinders? Hoses are only approx. 40" long. Also I have been doing a lot of ditch cleaning using the swing cylinders pretty hard.

Thanks

3/8" to 1/2" hyd. hose OK?

580k exhaust manifold bolts will break

Would like to change the exhaust manifold on a 580k. The bolts that hold the manifold to the head are badly rusted. If they break, how are they then removed? drill out and hope you keep the threads? The bolt is harder then the casting, small diameter, would be hard to drill out.

580k exhaust manifold bolts will break

bulldozer rates

hi,
ive always been hiring out my machines on an hourly rate but now getting a job where im going to be paid per cubic meter!
so just wondering how to figure out rates for my d8n and d6r rates per cub and how much each machine would do in an hour?

bulldozer rates

Volvo L70F low brake pressure problem?

Replaced the accumulators still getting an error code,swapped sensors and still same.

Remove plugs off block under steps and comes up with error for fan and brake failure,fan must be slowing once warm as engine gets warm.

If my brakes were worn would excessive travel cause a low pressure fault?

Tia Eulb...

Volvo L70F low brake pressure problem?

D31PL-18 blade lift capacity for stick rake.

First post here guys, just bought a tidy D31PL-18 with 4000 hrs on it, it'll be doing light scrub clearing here on our 30, 300 and 600ac farms here in Oz, just pushing lantana, guava tree, and other light scrub/small trees to clear way for more pastures. I started building a stick rake for it recently and doing the sums on the steel it looks like it'll weigh in at 420kg worse case, its a 3m rake. Now the old man is in my ear telling me the dozer probably wont even lift it. Gotta say, I'm...

D31PL-18 blade lift capacity for stick rake.

D31PL-18 blade lift capacity for stick rake.

Komatsu pc 200-5 6d95 engine overheating

Dear professional members,
I recently had an issue relating to engine overheating,the engine had major mechanical component inspection on board but did not find any suspicious error and the hydraulic main pump was also adjusted to lower the engine load,which regarded as the main cause of the overheating but those did not give much difference,as the work operation was urgent,one spare engine was sent to replace it,improvement was,but not much,the previous installed engine was disassembled at...

Komatsu pc 200-5 6d95 engine overheating

Komatsu pc 200-5 6d95 engine overheating

metal particles in gear oil from final drives in takeuchi tl140

i changed the oil in my final drives on a 06 takeuchi tl140 with 700 hours. this was the second time i changed oil. old oil came out frothy...with air bubbles. and the old oil had lot of metal "glitter" in it. i installed new oil and ran for a bit and drained it out, and replaced with new oil. ran another few hours and replaced oil again. still see "glitter" in the drained oil.
should i be concerned? running 75w-90 oil. would thicker oil provide more protection?

metal particles in gear oil from final drives in takeuchi tl140

Takeuchi 135 Restoration Project

I just purchased a 2004 Takeuchi 135 that recently caught fire from a brush fire. It burned the rear of the excavator melting all the wires, burning hoses, fan, etc. I bought it real cheap and plan to restore it. The machine was off at the time of the fire. I plan to pull the engine, purchase new wiring harness etc and fix up. I stopped by the dealer to order the manuals; however, does anyone have any experience with working with this brand of machine? I figure I will start by buying...

Takeuchi 135 Restoration Project

Takeuchi 135 Restoration Project

which used 10 thru 12 model 5 ton mini zero swing?

looking for a 5 ton zero swing mini 10 thru 12 model around the 2000 hr mark, which unit would best hold up to normal use, and not be a bag of bolts after some hours of use??

which used 10 thru 12 model 5 ton mini zero swing?

The Schield Bantam

Here's another classic machine article, which I've just uploaded to our website.
http://ift.tt/2qzhDbW

The Schield Bantam

1969 580CK - Broken Transmission Gears

Hi everyone, I've been lurking around the forum for some time now but am hoping you guys can help me with my latest problem.

I recently purchased a 1969 580CK diesel with a power shuttle and 4 speed. I bought this machine not running with a broken ring gear on the flywheel. Over the course of a few weekends, I managed to split the tractor and replace the ring gear successfully. This is my first piece of heavy equipment so I learned a lot along the way.

Once the tractor was running I went...

1969 580CK - Broken Transmission Gears

1969 580CK - Broken Transmission Gears

Wearing the paint off the bucket

Finished rebuilding the bucket last fall & hardly any snow this past winter, so the old 941 that I purchased the year before sat practically all winter. Today I was able to rough out a pile of fill left from a driveway dig out that was done this past winter in the back yard. We are in an area of really heavy clay, so it is very slow to dry out in the spring. If we don't get rain for a few days, I can go over it again to touch it up. The old machine runs real good for its age.

Wearing the paint off the bucket

Automatic Lubrication Systems

Hi All,

I am not sure if this is the correct forum to post. If not, please move to the correct one.

We purchased 3 Volvo EC300DL excavators 3 months ago. Now, I am researching Automatic Lubrication Systems for the machines. My questions are:

1. Do you advise to use ALS?
2. There are two different models as TWIN and SKF KGF. Has any of you used one of these models? TWIN is twice as much as SKF. Does it worth the value?

Thank you in advance

Automatic Lubrication Systems

Blumaq parts

Does anybody have experience with parts from Blumaq? They appear to be pretty large and based in Spain but I don't see many opinions on their quality.

They do supposedly have parts that Volvo can't get for me so I'll probably have to try them. Just wondering what to expect.
Thanks.

Blumaq parts

515 international loader

I have a 515 International Dresser and need to find the parts to repair the transmission model S-710. Please let me know where can I get the repair kit inclusive of the clutches

515 international loader

Tire cost?

Hello fellas. A question from Russia what tires do you guys prefer for your Raptor.?And how much Michellin 440\ 480 R28 cost? Here it costs 1500$ one tire

Tire cost?

DYNAPAC CA 151

just wondering if anyone has had to replace a rotted out muffler on a ca 151. just checked with dealer and there looking for 2600 for a new one. I'm sure no one has replaced to OEM. going to look for something similar to fit, anyone use a specific truck muffler?

DYNAPAC CA 151

What are the essential tools in your shop?

Okay- we were broken into the day after thanksgiving, and they took most of the tools out of my shop building. I ended up getting 95% of it back after chasing them down, but that's not what this is about.

What this is about-- I was faced with a Monday morning, with most of the tools gone, and trying to go back to work.

We managed to scrounge up a couple sets of sockets (1/4",3/8",1/2"drive), ratchets and combination wrenches, and a couple hammers (big and bigger, the only two sizes...

What are the essential tools in your shop?

What are the essential tools in your shop?

215 Cat

I have a 215LC, 96L02812, that has no power while traveling and turning. All operations will still function while traveling, swing, bucket, boom, which is not suppose to happen with a 215 when it is in full travel. I thought it might have been the swivel, but now I'm thinking it might be the turn and direction control or pilot valve. Thanks for any information or recommendations.

215 Cat

Samsung Engine Load Problem

I bought a Samsung SE210w 2a last year and only just started using it to clear some land on my farm. It hadn't been used for some time before I bought it and have done some significant work on the engine before beginning. However, it is now stuck and seems to have a hydraulic problem I suspect resides in the control valve.

Last week, whilst pulling out a coconut tree stump, my assistant indicated to me that there was a leak coming from the engine. I jumped out of the seat and looked under...

Samsung Engine Load Problem

Samsung Engine Load Problem

komatsu PC290 LC engine ignition security password forgotten

hi
forgotten komatsu PC290 LC engine ignition security password. Is there master password or any means to break this password.

thanks

komatsu PC290 LC engine ignition security password forgotten

Bobcat 773G Electronic Service Manual

Does anyone have an electronic verison of the 773G service manual they could share? I saw a partial table that contained voltages for certain connectors and would like to see the rest of the table. I have a service manual for an 873G but it doesn't include any table with references for expected voltages for any of the connectors. This particular table was for the AHC Controller. If you can't my email from the profile, let me know.

Thanks

Bobcat 773G Electronic Service Manual

Spanner wrench for Hyd Cylinders

I need to put new seals in the tilt cylinders on my A300. What kind or brand of spanner wrench do you guys use?

Spanner wrench for Hyd Cylinders

Liebherr roaring noise when slowing down

Hello All,

We have a Liebherr L566 wheel loader. Problem with the machine is that it makes a roaring noise when slowing down. If brake are applied the roar is louder. Truck has a 3 speed gearbox with hydrostatic drive and when shifting gears it has difficulties and it looks like it switches them in delay. So that gears stay longer.
No errors found, no warning signals, hydraulic oil is ok, hydraulic oil filters clean, transmission oil and transmission oil filter renewed. Gear pump that...

Liebherr roaring noise when slowing down

Liebherr roaring noise when slowing down

belaz 75710,Opinions about wheeled dumper built in Belarus

What do you think of the giant belaz 75710 mini-tipper truck, built in Belarus, if possible I would like to have honest opinions on this truck thank you, maybe if you know any good defects, curiosities would be welcome news thanks to the next.
I hope i will not be like davide and golia, compared to other dumper as performance all appearance, only muscle steel if i can afford the comparison

...

belaz 75710,Opinions about wheeled dumper built in Belarus

belaz 75710,Opinions about wheeled dumper built in Belarus

Cat dozer, did not turbo or engine start puking oil?

I will try to condense my post. Went to run my old D7E. Has not run in maybe 5-6mo. Knew the turbo oil return tube was leaking, always has. Realized during repair that the tube was not long enough because turbo probably was not set perfect but I just machined a quick shim to get this sealed and move on.

Got machine going. Nothing abnormal other than I knew the machine had some blowby and seemed quite a lot in the higher wind. Remember checking it a few times. Was mostly just warming...

Cat dozer, did not turbo or engine start puking oil?

Cat dozer, did not turbo or engine start puking oil?

Manaul for Hitaxhi EX 50-URG

Anybody have a manual for a Gray Market Hitachi EX 50 URG. Its a 1992ish model. I have a Parts Book (not alot of help) for this machine but would really like to get a Operators manual or any other books available. I also have the manual for the 3 banger Isuzu engine. New, Used or Photo Copied would be a big help.

Next dumb question is:
What does the URG mean?

Regards
Charlie S

Manaul for Hitaxhi EX 50-URG

British Columbia Forest Products Ltd.

Well HDX and Trakloader I grab the challenge starting this new thread British Columbia Forest Products Ltd.(BCFP) Company dates back to 1946. It was merged of several companies. Once it was the 3rd. largest lumber producer in Canada. Looking forward to see some great posts:canada
Now gone - it's a shame

British Columbia Forest Products Ltd.

Link Belt Swing Issues

Hello gentlemen. I believe I've made some headway on my excavator. Upon pressure testing I have found that I had no unloader pressure (which would be my set pressure.) I believe that is why it would not let my swing brake release. This set pressure from my unloader valve had a line going directly to my left and right swing spool which may be giving me my non brake release problem.

I also disconnected the free swing valve and plate underneath the brake by plugging them. Has John C....

Link Belt Swing Issues

Link Belt Swing Issues

550 case vibration

Anyone familiar with a 550 case, I believe its a 91.
I starts great, Idles smooth but vibrate when you rev it. it rattles the screens on the Rop. Its not real bad but Ive ran other 550's that rev smooth, so I'm looking for the problem. I looked at the drive shaft and seems to rotate free.
Is something loose or bent maybe. Looking for suggestions to check from anyone. I'm more of an operator then mech.

550 case vibration

Cat 259d or 289d Deere 323e

I have owned a deere 323d for several years. Overall it has been a comfortable machine, but it has had a few electrical issues along the way and I'm ready to upgrade to another machine.

A little background on us. We build houses and do a lot of concrete work on our own stuff as well as subcontracting work for other people. We do all of our own dirt work, so wanting a machine that doesn't struggle too much when back filling and moving dirt. Sometimes there's a lot of travel involved, so...

Cat 259d or 289d Deere 323e

Cat 259d or 289d Deere 323e

How to calibrate Joystick Genie Z60-34 year 2002

Dear all,
We have 1 issue with Genie Z60/34 year 2002. The main boom joystick has problem with boom up function. Other functions work normally.
We tried to calibrate the joystick as mentioned in the manual.
However, after calibrating, the joystick didn't work (all functions of the joystick didn't work).:Banghead
We didn't hear any error alarm. We haven't checked the fault code yet. But we don't know how to check the fault code.
To make short, as the moment we have the main boom joystick...

How to calibrate Joystick Genie Z60-34 year 2002

How to calibrate Joystick Genie Z60-34 year 2002

Can't figure out how to edit my signature?

Title says it all. Need some help

Can't figure out how to edit my signature?

Genie Z45 overheating problems

Good day

Can anyone help me please....
I have 3 x Z45 R/T 2008/9 models.
I never used to have an issue with overheating but lately they get VERY hot and actual trip the engine(Deutz). All 3 are doing this now. All functions are working well, no problems.
I had a look on the function manifold and used Testport 1 where I get 230-235 bar which I think is right, so it can't be building the heat from the main pressure relief valve correct?
Engine side I believe is good, engine air vents are...

Genie Z45 overheating problems

Genie Z45 overheating problems

GM Diesel, interesting how times change...

Got hired by Union Pacific out of Roseville but in the meantime been working for a company in Stockton building Detroit 2-Strokes. So interesting how times change, I'm working with one other mechanic 69 years old and he's been at it since the 70's but he can't last much longer. Such beautiful engines in my opinion, the 53, 71, and 92...just sayin...strange to be working on these engines in CALIFORNIA where they have become practically obsolete.
View attachment 170041 View attachment 170042 ...

GM Diesel, interesting how times change...

GM Diesel, interesting how times change...

KingPost Bushes

Hi Guys, i have an almost new excavator and if i measure the lower kingpost pin and bush clearance from side to side using a dial gauge i have .035'' or .889mm without putting a huge amount of weight on it which probably will produce more.
Has any one fitted new pins and bushes to a machine and got big clearances?
Is this normal for new or repaired machine.
Kubota agent says its fine but i think is very ordinary.
Any comments please.

KingPost Bushes

580 looking new

I haven't posted in a while, actually since I bought the 580 SE. Well a quick update. Before I bought it I had xgiaovannix12 check it out for me. He was at the time just someone I had been following here on the forum who seemed to have a really good knowledge of backhoes & it just so happened he was close to the machine & also to where I live. Well it checked out better then I had hoped for. John came with his father & gave it a good going over. I was so impressed with both that I asked John...

580 looking new

580 looking new

Case 580B - Removing the motor - What else should I be looking at?

Hi Everyone,

I picked up my first loader this weekend. This is a 1973 with the torque converter drive and 188 diesel. Being my first loader, it is also my first time working on such a loader. The 3" thick Service Manual should give me plenty of reading materials and tell me many things I need to know, but I could sure use your experience on a few questions.

I will be pulling the motor out of this unit. It has about 3700 hours on it but sprung a coolant leak into the crankcase. Previous...

Case 580B - Removing the motor - What else should I be looking at?

Case 580B - Removing the motor - What else should I be looking at?

D9H refurb: The boring bits

So if you are interested in boring bits of a D9H dozer refurb, you are only slightly less deranged than the person posting such rubbish (me). Here is some photos of the end result of toil this evening. I can only work on the dozer in the evening when the kids are in bed and wife has given up with running cups of tea to the shed, as I work 40 hrs a week in an office job I hate and any spare time the kids are awake is devoted to them. I am working on salvaging any thing I can from the cab, so...

D9H refurb: The boring bits

D9H refurb: The boring bits

D4h2 angle spool

Is it possible to replace the blade angle spool without removing the unit from the machine...

D4h2 angle spool

D7E brake bands

A friend and I started replacing the brake shoes on my D7E today. The current band that's on there is a 1 piece. I'm curious if there's a OEM or aftermarket 3 piece band that will fit back in there that is the same size. Thanks for any help!
Chad

D7E brake bands

Roadway dust control

So working with a modest budget, the goal was to be able to put some water on the roadway, better part of a mile of pretty heavily traveled road and parking lot, dust is sometimes a problem. With a little napkin R&D, some wood blocks and four IBC tanks, we came up with a nice solution. 4 tanks in the dump truck, 1100+ gallons, all gravity and a discharge rate of 60gpm, easily installed and removed in 15 minutes or so. It really looks like chutes and ladders but it does work pretty well...

Roadway dust control

Roadway dust control

Ran a track off !

I guess this really is an example of a track run off !

http://ift.tt/2r6hZuo

Ran a track off !

Cat 312 every function SLOWS when hot

A purchased 312B -
When cool/cold hydraulics are strong. After working and heating up the hydraulics get weaker. Travel is slower and will not pull out of a steep area. Swivel is slower, hydraulic pump 'noise' sounds 'noisier'. Digging is less 'strong'.

As a -purchased- Cat I was wondering if 'old' hydraulic OIL might be the cause. Lower VISCOSITY under heat ?
Or . . . is the PUMP not putting out the VOLUME at higher temperatures.

45 gallons of hydraulic oil is -expensive-. . . . ....

Cat 312 every function SLOWS when hot

Cat 312 every function SLOWS when hot

Hitachi EX200-2 Diodes

Hello I am back again and need some help. I recently employed the services of an electrician to installed a alternator which I gave to him days before in order to make sure that everything was OK with it. After the site visit and he left I notice that I have no monitor lights on start up and cant rev the machine so I disconnect what he did and reinstall the old alternator and fuses that was burnt and was able to rev the machine to move it.

There was only three lights on the monitor...

Hitachi EX200-2 Diodes

Hitachi EX200-2 Diodes

Cat 312 won't spin

Hello, My 2000 model year 312 BL won't spin. I think it is either the solonoid on the turn motor or the sensor that tells the solonoid to release the brake. I did realize that it was heat related. It started doing this last week. I would be running it for a while and it would stop turning. I let it sit for a half hour or so and it is normal again. I run it for a while and again it stops turning. Today it stopped and after letting it sit a couple hours it still won't turn. Whatever was on...

Cat 312 won't spin

Cat 312 won't spin

JD 544e forklift questions

NEW Here but not new to Equiptment

JD 544e forklift bout right and its AIRFORCE low hrs. Hope to get it set up and rented/leased

retire from army in 2 mths!!!!

I need a bucket so looking for kits ect and found a wore out 544g

is there any reason i cannot change to the G Bucket setup with arms and all and sell some parts off the g and come out ahead?

Lord they want bunch of $$ for a coversion to bucket used.......

JD 544e forklift questions

Windshield Replace Hyundai Difficult?

Just got a call and my 140lc 9 has a busted windshield (Front Upper) glass only no other damage. Does anyone know if this is a specialty fix to replace or can somebody with a little knowledge get it done. I found the glass for a reasonable price and it states that it doesn't come with hardware, only glass, can i use the existing rubber and hardware. If this is a job that needs special attention please save me some time and speak up.

As always help is appreciated.

Jerry109999

Windshield Replace Hyundai Difficult?

Greetings from up north...

Greetings my new friends, I'm 59 and a city boy at heart. Spent most of my life as "the boss" in retail endeavors. After my business life ended I retired up to northern Maine.
I never thought I would find happiness behind the wheel of a backhoe, but needing some work done on my property, I spent quite a few months looking around the internet and the best, inexpensive unit I could find was a glorified lawnmower with a bucket attached for 3500 bucks, No way I said to my buddy!!

So we kept...

Greetings from up north...

Greetings from up north...

Aftermarket parts?

Anyone have luck with aftermarket parts for heavy equipment? If so what brand or company are you working with and what kind of warranty are you getting? I run a repair shop and can't get discount at the dealers so I can't mark the parts up when the customer can buy them over the counter for the same price. Looking for some insight from what you independent guys do. Thanks

Aftermarket parts?

Bobcat/melroe hydraulic breaker specs

View attachment 169137 View attachment 169138 View attachment 169139 I know it's an older unit and was wondering if anyone could shed any light or give some specs on a melroe 25006 breaker/hammer. If parts are still available and any break downs or manuals for it also. Thanks in advance.

Bobcat/melroe hydraulic breaker specs

Just some work pics

Just thought I post up some pics of what I've been up to. Sorry about the sideways pics, I tried rotating them in windows, but it didn't stick.

View attachment 157749

View attachment 157750

View attachment 157751

View attachment 157752

Just some work pics

Caterpillar 3406B serial number lookup?

I am about 48 hours away from buying a used (85-86) 3406B Cat engine, one that's out of an old Autocar and the guy that's selling it to me was going to use it for a different application in a soil aerating machine. Turned out he didn't use it because of different bell housing and other issues that wouldn't work for him, so he's listed it for sale. I came along and lo & behold, I needed one anyway.

It's tough going by what somebody selling something is telling you. He claims it is a...

Caterpillar 3406B serial number lookup?

Caterpillar 3406B serial number lookup?

life expectancy for JLG boom lift

Hi

I've been given the task of searching for a boom lift in particular a 450aj sII JLG to go along side another of an identical model, since I've only come across one that has 5000 hrs, I would like to get some indication of if this is high hours for this type of machine, I'm more familiar with earthmoving where equipment is naturally in a rough environment.

What kind of hours have people seen on these machines before doing anything major ?
The other machine is currently around 3000hrs...

life expectancy for JLG boom lift

life expectancy for JLG boom lift

New Holland LB75B Starter Issues

Hi everyone,

I just joined hoping i could get some help on my backhoe! Thank you in advance for your time and help. I'll try to make this as concise as possible as it has been quite the journey.

I have a New Holland LB75B backhoe that's around 15 years old. I'm not sure of the exact age. My starter issues all started when the battery was constantly being drained to the point where I had to jump it even after one day. From this I determined the battery was no good and the starter was...

New Holland LB75B Starter Issues

New Holland LB75B Starter Issues

Help identifying hyster

I purchased a hyster forklift and cannot find any tags on it. I did find the serial number stamped into the frame it is. C5D 15025 any help would be greatly appreciated. I'm trying to find year and model. I would feel better knowing the lift capacity.

Help identifying hyster

john deere 450 g vs 450 H

Ok, looking to buy one of these to maintain roads and other light work. some have advised get the H with the joysticks, others advised get an G, so it would be easier to repair.
some have advised to not get anything earlier than a G, due to different problems .
whats the pros and cons comparing these 2 units. ?

john deere 450 g vs 450 H

Good compressor for media blasting

I need a compressor to media blast with. Hoping to get something in the 175CFM+ range. Price is one of the more important considerations right now - but of course not something that will be a headache. Are there brands to stay away from? Or a number of hours where it just makes no sense to buy? I don't know much about the whole thing but we are getting ready to do a bunch of blasting (soda/glass/coal) and just want to make sure we don't pick up anything is all wrong for the task.

Good compressor for media blasting

JLG 45HA Hydraulic Issue

I have a JGL 45HA. I capped the ports on the drive valve, and when operated one way, I can get it to the 3000 psi it should be. When I go the other way, it only gets to about 2400 psi. I swapped a valve cap end with a different function, and added shims to the spring, but no change.

The odd thing, is when I function another function, it will jump up to the 3000 psi, but not the drive function by itself.

I was curious if the dump valve could be causing this, but it seems like it is...

JLG 45HA Hydraulic Issue

JLG 45HA Hydraulic Issue

JLG hydraulic test coupler ?

Can anyone tell me what type of quick connect I need to check/set hydraulic pressure on a 40H boom lift with vickers valves. JLG sells a whole kit but I have the gauges and other stuff just need the quick connector. I know it's not pioneer or H-type because have both of those and they don't fit. Was thinking it might be ISO-A or ISO-B?

Thanks

JLG hydraulic test coupler ?

Shuttle shift problems

Good day gentlemen. Ill describe to the best of my knowledge what I've been experiencing. A year ago, I had purchased a 1973 Ford 4500 backhoe with a 4 speed power reversing trans (shuttle shift). When I first got it home, I had moved it to the back yard, and in doing so I was shifting through gears to make sure that everything was operational. As I got into 4th gear, it came to a rolling stop. From this point, I have tried numerous times to assess the problem. I have had a number of...

Shuttle shift problems

Shuttle shift problems

JLG 40H confused about the proportional dump valve

I just bought a 40H and I don't have drive or lift and the swing is very slow. It is a standard control machine with the LSG423 engine and vickers proportional valves. I checked voltages at the proportional coils and they have good voltage and are pulling strong. There are 2 valves that are called dump valves in the parts book and someone marked them with a PV on the machine at some point. One of them is small with#4 lines going to it and is mounted just aft of the proportional valve on...

JLG 40H confused about the proportional dump valve

JLG 40H confused about the proportional dump valve

Fixing Pumps over the phone

I get calls, maybe 4-5x a week from independent tractor mechanics wanting to know this or that & how to fix a leak or how to get a tractor out of the field.. What to check & how to fix it.. OR how to pull a pump.. and I tell them..
It doesn't cost me a dime to "help out".. OR so I thought..
I started saying>> "I'm sorry but I no longer fix pump/tractors over the phone.. IF you would like to bring me the equipment, I'd be happy to have a look at it for you.. OR you can pull the pump & bring...

Fixing Pumps over the phone

Fixing Pumps over the phone

New Guy from Canada!

Hey, long time lurker, figured I'd finally make an account and start contributing in the discussions!

A little about me, I'm a 27 year old HD mechanic apprentice, previously a spent 5 years as a helicopter tech (AME-S and components). I'll be getting my HD ticket in the next year or two depending on school wait lists. Been working on equipment almost 3 years now and have all my apprenticeship hours completed. Always open to learning and honing my skills, I take a lot of pride in my work and...

New Guy from Canada!

New Guy from Canada!

Demolition, clearing and grading

I have been planning on doing this for a while and will post some pics of our work. We are a family owned operation and do a little bit of everything so that is why you will see us doing all kinds of stuff in the pics. I w ill try to put some pics aon at least once a week. Wolf requested some pics of our demo work so i will start with a few of those.


View attachment 118963


View attachment 118964


View attachment 118965


View attachment 118966 ...

Demolition, clearing and grading

Demolition, clearing and grading

New CAT 1055F and Moba Big Quad Ski

Had the opportunity to install a Moba Big Quad Ski today on a brand new CAT 1055F Paver. If you are doing main line paving and looking for the smoothest possible ride then contact me about a Moba Big Quad Ski. We can also upgrade your current 3 sensor ski to a quad.

New CAT 1055F and Moba Big Quad Ski

History of Champion Motor Graders

Hey guys, I have been given some priceless pictures and brochures of the early years at Champion Road Machinery....actually it would have been DRMCO...Dominion Road Machinery. Some things have dates and some dont but regardless, you grader lovers will enjoy looking at some of this. I hope you enjoy and it creates lots of discussion. Its a lot of stuff so I'm going to try and put something new on here every week till I get it all.

These pics are around the 1950's and 60's and are at the...

History of Champion Motor Graders

History of Champion Motor Graders

Leeboy Grader

I haven't find a topic about Leeboy grader. I know types like 635, 685 and 785.
Now I was on their homepage and find only one type, the 685C:
http://ift.tt/1hGOtD9

It seems they had reduce their types of only one.

Leeboy Grader

Section for komatsu d20,21 and similar grey market dozers

I created this thread to hopefully discuss komatsu dozers, in order to help people like myself that have a komatsu dozer and have questions about them.

Section for komatsu d20,21 and similar grey market dozers

Small Engine Gas Cap

I went to use my garden tiller this morning.. its a Husqvarna 900??
Anyway.. it started for about 10 seconds & died.. acted like it ran out of fuel..
I knew it was full so I went straight into diagnosis mode..
I pulled the fuel line to the carb & nothing came out.. I loosened the fuel cap & she poured out..
I didn't know small gas engine caps were vented?? I'm over 50 years old & this is news to me!!!
It was 90* outside & didn't go any further w/any fixes, just left it loose & tilled the...

Small Engine Gas Cap

Small Engine Gas Cap

1984 GMC C7000 366

I have a truck that has been sitting since 2010. It is not running. It turns over, It was not getting gas, I replaced the fuel pump and now am feeding it from a gas can. It is now getting gas

I don't think it was getting spark, I replaced the distributor cap, rotor and coil. still nothing. there are 4 wires into the distributor cap, a red, yellow and two plugs. I guess red is 12 volts, yellow is grounded through the ignition switch???

The plugs are Autolite 144s, they are carbon coated...

1984 GMC C7000 366

1984 GMC C7000 366

2012 D6K Fuel System Problem

We are having problems with our D6K fuel system. Throwing code but no problems show up on computer. Losing power. Appears to be problem with the high efficiency fuel filters. When those are replaced all is well for a while then problem reappears. As near as we can tell it is a problem with the fuel. There is a black film inside the tank. One mechanic says it is a fungus in the tank. Has anyone experienced this problem? Mechanic says take tank off and steam it out. Will this work or...

2012 D6K Fuel System Problem

2012 D6K Fuel System Problem

Case 1845C control arm - reverse issues

I'm having an issue with my CASE 1845C. The right side control arm does not operate in reverse. It works going forward. The left hand side works fine in both directs. What could be some simple trouble shooting ideas I can look into before spending a lot of money at a repair shop? Some linkage items or grease fittings? I'm hoping it not anything expensive like a new pump. A possible related issue is that the right hand bucket control also has issues going back into neutral. The right hand...

Case 1845C control arm - reverse issues

Case 1845C control arm - reverse issues

How to tell if machine is equipped with " High Flow Hydraulics "?

How can you tell if a Bobcat s185 has high flow hydraulics?

How to tell if machine is equipped with " High Flow Hydraulics "?

Memories for us old truckers

Oxbow started this thread at the HTF forum.

Truck Shop



Memories for us old truckers

Standard flow mulcher

Hi, I was trying to find a mulcher for a standard flow skid steer and the only one I could find is the SS Miny Might. I couldn't find any reviews on them. Does anyone have one, or know someone that does? And if so what do you think about them? Also is there any other mulchers that will work for a standard flow skid steer?

Standard flow mulcher

Dozer blade

Does anyone use one? Seems like a good idea on my pt80 but no one even rents one in my area. Maybe that's my answer. Thanks

Dozer blade

2010 CaseIH Steiger 335 excessive oil use

Ok, boys. Quick rundown. The planter tractor has developed a rather concerning problem. Engine is a Cummins QSL, no after-treatment emissions controls. Started losing oil pressure the other day. Added 3 gallons to get to full, 145 hrs on oil change. Normal use is around half-gallon in 250 hours. After hooking up a manual gauge, discovered tractor was showing about 10 psi less than the gauge, so changed sensor. Now, tractor was showing less than 5 psi difference, but still throwing...

2010 CaseIH Steiger 335 excessive oil use

2010 CaseIH Steiger 335 excessive oil use

Kubota SVL90 undercarriage replacement

Hey everyone.. got a svl90 and the undercarriage is nearly done! Just wondering if anyone has replaced or rebuilt any? Suggestions for parts?

Kubota SVL90 undercarriage replacement

SVL75 - Shattered Door Window

Dayum,
Using grapple to clear some cut mesquite brush and BAM, piece of mesquite shot up like it came out of a rifle and shattered the door in a million pieces. Certainly got my attention! New unit, just 35 hours.
I imagine it's not going to be cheap to replace the thing. Problem is what's going to keep it from happening again? I wonder if they offer an option with ballistic glass

SVL75 - Shattered Door Window

So, John deere engine rebuild kit.

Longer range planning! 644E loader John Deere sixty something engine umm, let me see I think its a 6076T sounds about right, well so in planning the fixing of a moderate oil leak from the ass end of the block, I stumble across engine rebuild kits, some are deere and some are aftermarket or a mix of oe and aftermarket. All of it seems good assuming that the crank and rods are all standard size.

The loader has about 25,000 hours on it, so our best guess is that its on the tail end of...

So, John deere engine rebuild kit.

So, John deere engine rebuild kit.

What in the heck is wrong with JCB parts book?

I have a 1995 JCB 214 series 2 backhoe. Serial 3 SLP214CSE0433511 I need a 45mmX330mm pin for the dipper ram (rod end). I had the dipper cylinder rebuilt and am replacing the pins and bushings. I have all the proper bushings and seals, but the rod end takes a 45mmX330mm pin. I have a parts book and it always points to a 50mm pin. THIS WILL NOT WORK!!!!!!!!!!! The seals and bushings are 45mm and already installed. They fit perfectly as does my old pin.

What in the heck is wrong with JCB parts book?

Never think you can't teach a old dog new tricks.....this site is great

Never would have thought Cascade dishwasher detergent would bring a plugged radatior back to life.....can't thank everone enough for the help.

Never think you can't teach a old dog new tricks.....this site is great

The "not so heavy equipment" photo thread

Hey guys, thought I'd share a few photos of my work here in Tejas. For a little background, after owning a concrete company in SoCal for a long time with way too many employees, I knew that's not what I wanted to do here. I ran skip loaders and backhoes as my company needed and worked for an excavating company in the mid-seventies, so taking it up on a smaller scale was a no-brainer. Now I work by myself 99.9% of the time and really enjoy what I do. I typically work in rural areas for...

The "not so heavy equipment" photo thread

The "not so heavy equipment" photo thread

96 JD 310D shift issues

New to me, 4 in 1 bucket, extend a hoe. New reverser, torque converter and solenoids. Worked great for a day and a half then lost neutral, has forward, reverse and neutral position is still reverse without the horn. What happening?

96 JD 310D shift issues

Sumitomo SH200 Help

Hello,
I am looking to purchase a used Sumitomo SH200 excavator. The machine will start and run, but will not move at all because of something with the safety lever. The seller said that over the last few years he would have to "jiggle" the safety lever for the controls to activate. Now the machines won't move at all no matter what you do with the lever. He said that he has had a few mechanics come take a look at it, they have tried replacing switches, but not one can fix it. Can anyone...

Sumitomo SH200 Help

Sumitomo SH200 Help

580k exhaust manifold bolts will break

Would like to change the exhaust manifold on a 580k. The bolts that hold the manifold to the head are badly rusted. If they break, how are they then removed? drill out and hope you keep the threads? The bolt is harder then the casting, small diameter, would be hard to drill out.

580k exhaust manifold bolts will break

Thermal imagery uses

The Snap On guy came around the other day with a new toy to peddle. I was out and about in the field, but he got his hooks into the boss trying to sell him on a new thermal imager for $1200. He was pitching that you can use it to find bearings going south, misfires (finding a cold exhaust manifold runner) and short circuits in wiring. I have no doubt it will do all of those things. My question is, is it worth $1200?! I have a nice Klein infrared thermometer that I can do all of those things,...

Thermal imagery uses

Thermal imagery uses

Hydraulic cylinders-buying online

Good morning all,
It has been awhile, hope everyone is digging away!!
I have worn out stabilizer cylinders (among others) that need repair. I went to the local shop for an estimate (ouch!!) and decided to check online for a new one. Found several sources staying away from imported junk, and I can get new for less than a rebuild. International Hydraulics is one of the companies (they are linked on this site).
Any thoughts on this? Has anyone purchased cylinders online and how is the quality?...

Hydraulic cylinders-buying online

Hydraulic cylinders-buying online

Volvo L70F error codes?

Hello,is there anywhere I can find a list of these?

Tia Eulb

Volvo L70F error codes?

Komatsu pw130 1997 and ls epc valve output from pump controller

We have been tracking problem with this unit for some time. Related on stalling on bigger load.

After checking pilot pressure and ls pressure, we noticed that ls epc pressure does not chage at all. Based on shop manual it should. Output voltage for ls epc valve is only 7V, mA values seems to be ok. With travel speed epc valve it gives 24 and 0-1000mA, just like maual says.

Cables are replaced and ok. Is there any other option than bad pump controller? There are a change that wires are...

Komatsu pw130 1997 and ls epc valve output from pump controller

Komatsu pw130 1997 and ls epc valve output from pump controller

Cat 305C CR swing/rotation problem.

Good day everyone!

I have a Cat 305C CR s/n HWJ005XX, on loan that I´m looking into purchasing. The current owner told me he had a issue with the swing/rotation of the machine.

When he had a full bucket far reach, and turned the swing to the left, the machine kept going(swong freely). But only when turning left, and when the machine is warm, it does not do this when cold.

I´ve tried to provoke the machine to do this, by getting it warm and swinging it(In a safe place). But I cant seem to...

Cat 305C CR swing/rotation problem.

Cat 305C CR swing/rotation problem.

CMI C175 Forestry Mulcher

We, KW Land Works, have a few hundred hours on this machine now. It's a beast compared to our Cat 297 but it doesn't replace the CTL all together. The craftsmanship and design are stellar. View attachment 169970 View attachment 169971 We've been thinking about putting a subsoiling head on it as of late. Everything I read suggests we need 300 hp so I'm hesitant. One of the head manufacturers we've been in contact with will hopefully have...

CMI C175 Forestry Mulcher

CMI C175 Forestry Mulcher

New to me 955K

Hello everyone. First post here. Ive been lurking and gaining information and Id like to thank all of you for all the posts. I scored this old 955K at a local auction not too long ago. I plan on using it to clear brush on my hunting ranch. It has been outfitted with a blade from a D5 or D6 but did come with the original bucket which is in good shape. The engine (D330C I believe?) runs well and makes good power. It is rather beat up an definitely needs a bit of maintenance. I started by...

New to me 955K

New to me 955K

Auction Backhoe - 4x4 missing front drive shaft

Was eyeballing an auction and they have a decent looking older case with 3.2k hours on it but its stated as missing the front drive shaft. Is that a bad sign of its life or would it be a good option to purchase and install a new driveshaft?
View attachment 169963
View attachment 169964 View attachment 169965
There are some images of what the under-carriage looks like

Auction Backhoe - 4x4 missing front drive shaft

JLG 600 AJ Drive / Break problem

Hi ,

Have a problem with machine ( 4x4 ) 600 AJ Model , when you drive the machine forward and reverse , it suddenly stop/break very harsh and hard , the hydraulic pump makes e high pressure noise and the machine grinds to a halt , if you release and apply the foot switch it drives again , this problem does not come up in creep speed , if you turn the speed control (yellow knob) just a little bit up to increase speed , then the fault occurs. Some suggestions was that the oil are hot maybe...

JLG 600 AJ Drive / Break problem

JLG 600 AJ Drive / Break problem

1988 Cat 953 - Caterpillar. My First Track Loader

Using my cat 953 track loader, mini excavator, and skid steer to repair a dam.

Cat 953 was recently purchased to move dirt, brush, level off stuff the skid steer struggled with.

So far It has been a great machine. When turning on the dam the rear of the loader is hanging over the lake. The holes being repaired are deep, big and steep. Pretty much straight down 10 to 12 feet. Not much room to work.


View attachment 91716

The beauty of a track loader. A wheeled...

1988 Cat 953 - Caterpillar. My First Track Loader

1988 Cat 953 - Caterpillar. My First Track Loader

Case XT Series vs 400 Series- ATTN KSSS

What is the difference between these two series- I am looking at the 90/95, 450/465 end of things. Body types seem identical between the radial-vertical models as far as I can tell, but what is the preferable of the two engines-hydraulic set-ups? I see a lot of love for the older Case stuff, (4-390 engine and the 1845c especially), but the consensus seems to be that they get worse with each new series that comes out.

Case XT Series vs 400 Series- ATTN KSSS

cummins NH 220 engine timing

Anyone here know anything about timing a cummins NH 220 engine, its the engine prior to a 855 cummins, some call them the same engine depending on who you talk to, it has a PT fuel system on it, first one I"ve ever worked on. Here's the question I have, there are two methods to time the engine, one for torque method, the other for dial indicator method I think its called, but there are two seperate settings on the valves, .011 cold setting on the intake valves for one method which we used...

cummins NH 220 engine timing

cummins NH 220 engine timing

new ride

I have been lurking for a couple mounths ,I just upgraded boom trucks (I'll be carefull not to call it a crane seems to be a touchy subject ) so I figured its a good time to join in. I'm a building contractor this makes my fourth boom truck, up grading every time. I got my 2006 32105 elliot with a sitty down thing on it ,on the road last week,I'll send picks when I figure out how to reconfigure pictures.
A big howdy to all that have entertained and educated me
Regards

new ride

Looking for Bomag BW172D operators manual

Does anyone know where I can get an operators manual for a BW172D single drum vibratory roller? I bought the machine today and will pick it up this weekend. Any help will be appreciated!

Thanks


Don

Looking for Bomag BW172D operators manual

JD 310 SG backhoe control

I have a 310 sg that the hoe controls won't work on. Outrigger and extendahoe works just no stick boom bucket or swing.
The seat switch tests OK at seat. I would like to find a schematic for this or get some input on what to look for.
Serial number is To310sg956193

JD 310 SG backhoe control

Service Manual Trading Post

If you need a manual post what you need. (PDF Format)

Maybe someone can help.

I have a lot of deere manuals and i need some caterpillar: specifically 420D

Service Manual Trading Post

Twin Steer or Reverse Steer Tag or Ideas?

Back story:
Monday of this week I found a knuckle boom crane (used chassis, new crane, at the dealer) that according to engineering report the truck weighed 42.6klbs on 3 axles, 23' spread from steer to rear tandem. The weight split was 12.2klbs/30.4klbs, 42.6klbs gross.

When they were doing the temporary tag Tuesday they had a weigh ticket showing 18klbs/29.5klbs and 47.6k total (yes, the total on the ticket is 120lbs more than the sum of the two axles).

Wednesday, coming into TN, I was...

Twin Steer or Reverse Steer Tag or Ideas?

Twin Steer or Reverse Steer Tag or Ideas?

Where to find a mpoor for a deere 333d?

Hey guys,

Figured I'd ask here. The guy I push snow for is looking for a motor for a 333d deere as the one he has popped a rod and 2 pis tons by the sounds of it.

Any leads on who to call would be great.

Thanks

Where to find a mpoor for a deere 333d?

Pros, talk to me about coolant testing. Nervous about wet sleeves

I have several older machines. I also bought my tractor with a fresh engine because the coolant ate up the wet sleeves and killed it. That tractor got an additive filter unit to leach stabilizers in the coolant.

For these reasons, it has really been on mind to test and check my coolants to ensure I am not hurting the equipment. But I don't think you can just stumble into Auto Zone and get much more than concentration strips. I do maintain proper concentrations but I know certain...

Pros, talk to me about coolant testing. Nervous about wet sleeves

Pros, talk to me about coolant testing. Nervous about wet sleeves

Lube for air wipers??

359 Pete. Replaced the motor with new not long ago. Don't drive in rain much so they must dry out. I shot WD 40 down the air hose to get inspected and it worked for abit but not long. Something good I can just introduce thru the hose?? LB

Lube for air wipers??

06 CAT 277B restoration

Ended up selling my old 74 case 350 crawler loader for this gem. Didnt quite get a super awesome deal, but there was just enough meat on the bone to seal the deal. (12k)

Engine runs, everything works except the high speed track option, it needs a new track, and the engine puffs and misses a little at high rpm-no load; but clears up when actually doing work.

Did I mention the pilot valves are leaking? oh what fun.

Turns out it does have a VE pump, please dont scare me <3...

06 CAT 277B restoration

06 CAT 277B restoration

Manaul for Hitaxhi EX 50-URG

Anybody have a manual for a Gray Market Hitachi EX 50 URG. Its a 1992ish model. I have a Parts Book (not alot of help) for this machine but would really like to get a Operators manual or any other books available. I also have the manual for the 3 banger Isuzu engine. New, Used or Photo Copied would be a big help.

Next dumb question is:
What does the URG mean?

Regards
Charlie S

Manaul for Hitaxhi EX 50-URG

Pics of your mini!

Hey guys. This is a thread to show your mini! I will start of with a 2007 bobcat 335. Cab, Hyd thumb, q/c 34in grading bucket, 24in digging bucket, 18in, digging bucket, ripper tooth. I love it!
http://ift.tt/2lHEfZ8

Pics of your mini!

AC 145T rolling dirt

Just saw this on another site, pretty cool, to see the old guys work...



AC 145T rolling dirt

Jerky lift cylinder Bobcat 743

The tilt cylinder works smoothly but the lift seems to stick then drop or raise too fast. Almost like it's going into float.
When I push on the top or bottom of the pedal it seems to stick then pops free. Almost lost a log off the forks a few times.
I checked the linkage and it is free. Could the valve spool be sticking or is there a pressure relief valve in there somewhere that could cause this?
I encountered this problem a couple of years ago but it went away as quickly as it started, this...

Jerky lift cylinder Bobcat 743

Jerky lift cylinder Bobcat 743

removing control valve.

I have a Bobcat 743 and am about to remove the control valve for repair. Does the engine and related parts have to be removed in order to remove the valve.
Does the hydraulic reservoir have to be drained first?

removing control valve.

Cat 262b bogging under throttle

This 'demon" has been around a while now. Machine runs great....half day. All of a sudden, starts sputtering and puking smoke. Not even half power. SOMETIMES...you can turn off, turn back on. Most the time, that only last minutes.

Next day, runs like bat out of hell for...half day?

Changed fuel filter MULTIPLE TIMES!

Someone suggested my fuel lines may have collapsed...on inside. Changed them. Thought I fixed...NOPE!

Sent to mechanic while back to check to see if something was in...

Cat 262b bogging under throttle

Cat 262b bogging under throttle

Junkayrd's work thread.....maybe haha

While I don't do stuff near as cool as most of you I figured I'd start showing what I do on a regular basis. I'd like to name my favorites on here, but being a father of five I've learned to avoid hurt feelings haha. I manage equipment for a small excavating company. We run a D11N, D7R, D5G, D65, Steiger 485 HD with two 19 yard pans, two 210 Linkbelts, 110 SD roller, champion grader, 627B and a couple water trucks. I do all the service work and 99% of the repairs. Just did steering...

Junkayrd's work thread.....maybe haha

Junkayrd's work thread.....maybe haha

1966 Cat D8H

Hello everybody, I just became a member of this website because I find it very interesting and educational, especially since I recently purchased a D8H with only basic knowledge of crawler tractors. I really wanted an old D9 but couldn't find one that was operational and in my budget of $10,000. My D8H came from a private seller in Holland, N.Y. and met the criteria I was looking for. It had to be operational, look decent and not too beat up and be in my budget of $10,000. I am not an...

1966 Cat D8H

1966 Cat D8H

Automatic Lubrication Systems

Hi All,

I am not sure if this is the correct forum to post. If not, please move to the correct one.

We purchased 3 Volvo EC300DL excavators 3 months ago. Now, I am researching Automatic Lubrication Systems for the machines. My questions are:

1. Do you advise to use ALS?
2. There are two different models as TWIN and SKF KGF. Has any of you used one of these models? TWIN is twice as much as SKF. Does it worth the value?

Thank you in advance

Automatic Lubrication Systems

Komatsu pc 200-5 6d95 engine overheating

Dear professional members,
I recently had an issue relating to engine overheating,the engine had major mechanical component inspection on board but did not find any suspicious error and the hydraulic main pump was also adjusted to lower the engine load,which regarded as the main cause of the overheating but those did not give much difference,as the work operation was urgent,one spare engine was sent to replace it,improvement was,but not much,the previous installed engine was disassembled at...

Komatsu pc 200-5 6d95 engine overheating

Komatsu pc 200-5 6d95 engine overheating

Land Grading/Leveling Help Needed

Hey folks. Been reading the forum, and finally decided to join and ask for some help. Couldn't decide what the proper sub-forum would be so hopefully this works here as I believe scrapers might be the best piece of equipment for this job.

Trying to learn as much as I can regarding grading/leveling before I reach out to contractors and surveyors regarding bidding my project.

I'm looking to convert this land to outdoor parking/storage, so essentially a large parking lot, and would like to...

Land Grading/Leveling Help Needed

Land Grading/Leveling Help Needed

Cat dozer, did not turbo or engine start puking oil?

I will try to condense my post. Went to run my old D7E. Has not run in maybe 5-6mo. Knew the turbo oil return tube was leaking, always has. Realized during repair that the tube was not long enough because turbo probably was not set perfect but I just machined a quick shim to get this sealed and move on.

Got machine going. Nothing abnormal other than I knew the machine had some blowby and seemed quite a lot in the higher wind. Remember checking it a few times. Was mostly just warming...

Cat dozer, did not turbo or engine start puking oil?

Cat dozer, did not turbo or engine start puking oil?

TD8E Idler - Track Adjuster Won't Move

I have a 1986 International TD8E that the track came off because I was an idiot and forgot some large boulders in the area that the grass had covered. As soon as it came off I stopped so the track stayed pretty close to where it should be in relation. I thought OK, raise it up, loosen the tensioner push the track back on and good to go. First I removed #17 and as i loosened it up some grease came out of a hole. I completely removed it, then I completely removed #18 with the #19 zero in it. I...

TD8E Idler - Track Adjuster Won't Move

TD8E Idler - Track Adjuster Won't Move

JCB 1CX/208 Newbie

Hi guys,

Just joined this forum. I'm not a contractor or equipment operator. I just purchased a used 2003 JCB 208HF with 760 hours. I have a large property in a rural area and bought it for snow removal and landscaping/maintenance (and for FUN!!!). I don't have any manuals with it, operators or service. I have not received the machine yet.. I bought it in NY state and I live in Nova Scotia Canada. I am having it trucked here. So any help or advice you guys can offer would be greatly...

JCB 1CX/208 Newbie

JCB 1CX/208 Newbie

Dozer Transporter

I just got home from Florida picking this up. I was the high bidder on GovDeals. My D5G hauler!

View attachment 169932

Dozer Transporter

CAT IT28B Loader *No Brakes*

Hey guys,

I have an issue with my 87' CAT IT28B, it has no brakes! It has an air over hydraulic system. I replaced an air line that had a hole in it, tested it out and no brakes. Compressor is working fine because the system keeps released air from the relief valve located on the air tank every 30 secs or so when at idle.

I press the brake pedal and I can feel some air pressure there and it makes an air sound. But no brakes what so ever.

Both master cylinders has fluid in them also....

CAT IT28B Loader *No Brakes*

CAT IT28B Loader *No Brakes*

OTT Skid Steer Over Tire Tracks Sand Septic System

I have to install a raised filter bed septic system for my new home. I have access to a 2wd backhoe, mini ex, and a bobcat S150 skid steer. Would it be worth while to invest in a set of over tire tracks for the skid steer or will I need an actual tracked machine to get the job done. This will be my first raised septic system but I may do more if it goes well. I would appreciate any input on the OTT's or tips on the install of the system.

OTT Skid Steer Over Tire Tracks Sand Septic System

Hough 65C Hydraulic whine

My loader has a loud whine in the hydraulics when I lift the bucket. Bucket tilt does no make noise, only lifting.
Any ideas? Oil is full, new filters and pump rebuilt.

Hough 65C Hydraulic whine

Inherited a Ford 555, where can I learn to use it?

My father-in-law passed away in 2016, and we inherited his 9 acre property and some heavy equipment, including a Ford 555 backhoe/front end loader.

He purchased it to excavate for the house he built and the septic system. The land is mostly flood plain with a river on two sides, but the house was built on a hill, and I need to do some terracing and erosion control. I also want to do some excavation for some raised beds on the flood plain.

I can operate his Kubota mini-tractor with FEL,...

Inherited a Ford 555, where can I learn to use it?

Inherited a Ford 555, where can I learn to use it?

Volvo MCT125C

Hi guys, I just want to vent for a bit about my real life experiences with the Volvo MCT125C tracked skidsteer with an enclosed cab. But first I just wanted to say that I have owned and operated a lot of small equipment and normally don't let issues with equipment bother me.
I bought the unit new in 2011 when Volvo partnered with JCB and introduced their new one arm machine with the cab door to the side. I like the idea of the side door because of the contract I had for the machine...

Volvo MCT125C

Volvo MCT125C

JD310C - hydraulic pump identification

Any documentation available regarding the type of hydraulic pump in a 310C. Based on my manuals and s/n 753+ I'm able to determine its a Sundstrand Sauer pump with attached steering pump. I wasn't able to gather any additional information in my manuals or the web. I understand more information is stamped on the pump but i was hoping to do research before I have to dismantle...there has to be more info available....any help would be appreciated.

JD310C - hydraulic pump identification

JCB 212S Hydraulic issue

Hello everyone. I have a hydraulic problem on a JCB 212 S back hoe. When using hydraulic levers hydraulics initially work then stop completely. If operator slowly opens hydraulic levers it works but when opened fully it completely stops. Original thought was maybe pressure relief problem but I see all spools in there respective control valves have their own relief valves and since all functions have the problem I ruled that out. I want to check pump pressure. Can anyone tell me where to...

JCB 212S Hydraulic issue

JCB 212S Hydraulic issue

Compactor for sale: 2012 Sakai SV510D for sale

2012 Sakai SV510D Series III Roller
Approx 2000 Hrs
84" Smooth Drum
Cummins Engine
Clean, Work Ready Machine!

Price and detail: http://ift.tt/2qkucbc



Compactor for sale: 2012 Sakai SV510D for sale

Back to the drawing/operating board

Been awhile since I posted anything on my back issues. Had pretty well died off to background but never quit aching. Ben on PT for several weeks now with the only improvement that the pain won't find a nest. Poor little gals working me over(love having 30 somethings young ladies man handle me) have come to conclusions, I am working very hard to correct what they find, they find something different occurring week to week starting with SI joint, moving to tight muscle/tendon groups, now...

Back to the drawing/operating board

Back to the drawing/operating board

D41P-6. Steering pump

Leaking between pump
And transmission. I'm replacing shaft seal and oring on pump housing. The old o ring had silicone sealed on it. Should I put silcone sealant on new one or just go with the new o ring. Thanks ​

D41P-6. Steering pump

Vancouver Island, BC. Logging at its Best!

Giant trucks, giant loads, giant machinery! Enjoy.

Vancouver Island, BC. Logging at its Best!

Distributor Trucks

Let's see them.

Distributor Trucks

which used 10 thru 12 model 5 ton mini zero swing?

looking for a 5 ton zero swing mini 10 thru 12 model around the 2000 hr mark, which unit would best hold up to normal use, and not be a bag of bolts after some hours of use??

which used 10 thru 12 model 5 ton mini zero swing?

Road Surface Rock Options

I'm curious what you folks have to say about surfacing gravel roads. I know a lot depends on rock type.

Around here we have roughly 3 types of rock used on roads. I am referring here to 1/2" to 1" minus with fines.

1. Hydraulic mine rock. This consists of 6" cobbles down to sand dug from the river bottoms where in some places it lies in enormous quantities. They crush the cobbles but a lot of the rocks are already smaller so they might only get broken in half once to make size. This...

Road Surface Rock Options

Road Surface Rock Options

Anyone in Missouri?

hey guys been thinking about moving to Lebanon, mo from California. Wondering what the taxi service job outlook is back there.

Anyone in Missouri?

Expected Clearance with new KingPost bushes and pin

Hi Guys, i have an almost new mini excavator and if i measure the lower kingpost pin and bush clearance from side to side using a dial gauge i have .035'' or .889mm without putting a huge amount of weight on it which probably will produce more.
Has any one fitted new pins and bushes to a machine and got big clearances?
Is this normal for new or repaired machine.
Kubota agent says its fine but i think is very ordinary.
Any comments please.

Expected Clearance with new KingPost bushes and pin

Help with Radio replacement on Cat259D

Hello, I got a replacement radio for my 2014 Cat 259D. I have the little removal tools which I thought would have made this an easy job. 1st mistake i guess... i inserted the tools till they clicked and pulled= nothing happened. pushed in a little further and pulled harder. Only thing that came out was my anger. pushed and pulled till I thought something was about to break and gave up and started work project. Is there something missing in this complex task of radio removal that I need to...

Help with Radio replacement on Cat259D

Help with Radio replacement on Cat259D

WANTED: GOOD CATERPILLAR EXCAVATOR BUCKETS (D LINKAGE 330CL)

looking for buckets for our fleet of 330c excavators, these are getting hard to find so we want to stock up. We will consider anything that fits these machines.

Roller wheel
Compaction wheel
Kelly wheel
GP bucket
Smooth bucket
Frost Ripper
Quick Coupler
54" Bucket
30" Bucket
60" Bucket

WANTED: GOOD CATERPILLAR EXCAVATOR BUCKETS (D LINKAGE 330CL)

Cat 980g implement pump nightmare

Lets start here. Serial number 2kr03824
980g series I

About 3 weeks ago we had lost the implement pump on the 980g. Pulled it apart discovered it had broken one of the small 1/4 inch Allen bolts holding the larger cartridge together(vane pump) and blew out the o ring seals on that end of it.

Got a brand new cartridge and seals installed everything and it seemed fine.

The pump somewhat whinned from the beginning at higher rpms but seemed okay otherwise. Less than 15 hours later it ****...

Cat 980g implement pump nightmare

Cat 980g implement pump nightmare

Buy Roadlux r116 Tires ?

One of my friends from united state are searching for Roadlux r116 Tires. Can anyone suggest best dealer?

Buy Roadlux r116 Tires ?

What is Roadlux tire?

I heard that roadlux tire are the new kind of tires from China and they are growing in market fastly . I need detaied information about Roadlux tires. help as soon as possible

What is Roadlux tire?

Old dozers for farm

Been looking ever since shut down on the 16B Allis that thank goodness is gone to someone else. I looked into the D7E at Lebanon MO, even made a call as to price negotiable where told no. No chance for inspection either unless put money down which is NOT gonna happen. Could not get a straight answer as to maintenance records, nor would the seller(supposedly NOT the owner) get a s/n for back chasing and checking pedigree. $20,000 seems a lot for a pig in a poke. Made a offer of $15k, was...

Old dozers for farm

Old dozers for farm

Some Days You Eat The Bear.......

A year and change ago I bought my first dozer. Spent the winter going through it. It had rubbed the tracks on both hydraulic cylinders for blade angle. The pivot points beneath the tractor were allowing a bit of motion. Some research revealed that the tractor was built with 15" wide shoes. Mine has 16". There isn't much clearance anyway, the 1/2" eaten up by the wide track it seemed too much. Reggie, worlds most experienced crawler mechanic said give in, cut the shoes inside. I looked into...

Some Days You Eat The Bear.......

Some Days You Eat The Bear.......

Web Site update

Looks real nice.

Truck Shop

Web Site update

Generator Set

Hi all,

Does anyone know a site to buy or rent a generator set? I found several sites, but not sure which one I should go for...

Generator Set

Wabco scrapers at work

With all the talk about big scraper operator's in California, thought I would give everybody a change of pace. Richardson Contracting out of Columbia South Carolina is still moving dirt with a fleet of Wabco 229F, 339F scrapers. These pictures were taken several years ago in Anderson, South Carolina. I think it was about a million yards at the local airport. They also have 5 TD-40 Dresser dozer for push loading duties. I believe Richardson still operates a fleet of over 30 Wabco's. It's...

Wabco scrapers at work

Wabco scrapers at work

WTB Trommel screen

Looking to build a trommel screen to run Topsoil and river sand thru. Looking for a used screen to use for unit. Would consider a built unit if price is right , will not be used much , but definitly need one.

WTB Trommel screen

Zacklift

I have been looking at putting together a tow unit for the trucking company I work for. And I think the
best way to go is build a truck with a Z353 Zacklift with 25,000 lb stiff legs and a 30,000 lb drag winch.
Looking at a 2000 379 Pete with a 450 hp Series 60 and 10spd with 3:55's. I will stretch it to 300 WB.
And just install some tool boxes and tandem fenders. Sort of like this one. But it will be a permanent
mounted lift.

Truck Shop

View attachment 167483

Zacklift

Zf axles

Can anyone help new with what kind of oil the dire trial take and do I need friction modifier.

Zf axles

Zf axles

Can anyone help new with what kind of oil the axles take and do I need friction modifier.

Zf axles

Excavator grading tips?

Long time lurker, first time posting.

Currently doing the slab prep for a light duty shop. Just got the 3/4" crush aka top layer roughly spread out.

Only machine I have access to is a cat 308 with the mini dozer blade, ripping bucket with a finishing blade welded on the teeth. First time doing finish grading. Several hundred hours on excavators tho. Just looking for tips and tricks on how to go about it. The walls and ceiling are already in. 24' wide x 40' long by 20' high. I searched the...

Excavator grading tips?

Excavator grading tips?

Hello from Ohio

Hello, my name is Dustin and I am from Ohio!

Hello from Ohio

Cat scraper Trans oil transfer

Wondering if anyone out there has come across this problem.
I have a 627E Cat scraper that is transferring the transmission oil from the trans into the diff housing.
I have drained the diff so no oil was left in the housing, then filled the transmission and started the machine and the transmission oil started flowing from the diff drain bung.
Has anyone else had this problem and do you know where the transfer would be occurring?

Cat scraper Trans oil transfer

Has anyone put an air intake pre cleaner on an SVL90?

The title pretty much says it all. The damn filter gets plugged so quick when it's dusty it couldn't hurt to put one on I imagine, has anyone done it?

Has anyone put an air intake pre cleaner on an SVL90?

D5C threw a rod. does cat 3046 = mitsubishi s6s?

Hi. I recently purchased a late 90's D5C dozer with a blown motor ( appears to have thrown a rod). It is equipped with a 3046 turbo diesel which is rated at 95 fwhp. A little hunting around on the net leads me to believe the engine is made by mitsubishi and is the same as the mitsubishi S6S. In fact the cat motor has S6S-D cast into the head. I have access to a running S6S from a cat forklift. The lift motor is a naturally aspirated version rated at 120hp. Seems strange to me that the NA...

D5C threw a rod. does cat 3046 = mitsubishi s6s?

D5C threw a rod. does cat 3046 = mitsubishi s6s?

Purchasing a new backhoe. Input and also to buy with 4-1, or upgrade with a 4-1?

Looking into purchasing my first backhoe, been researching/watching local for sale for about 6 months now. I run a farm and need to remove a lot of trees, trench and lay new waterlines/french drains, build 2 barns, and change the layout of the land a bit. I've been doing what I can with a 90hp DX90 tractor but no FEL and limited into what I can do with it. Im leaning towards a Case 580k or SK (preferably with a cab that I could upgrade with AC) as they seem to be a little cheaper then JD and...

Purchasing a new backhoe. Input and also to buy with 4-1, or upgrade with a 4-1?

Purchasing a new backhoe. Input and also to buy with 4-1, or upgrade with a 4-1?

manual for Altec AN546?

I dont suppose anyone would happen to have a manual for an Altec AN546?

manual for Altec AN546?

Cat 416 c linkage problems

Hello everybody. I recently purchased a used 2000 Cat 416c and I am having some issues with it. The backhoe scoop linkage arms broke and the H linkage bent. I replaced the arms and had the H link pressed straight and welded. I also replaced all the pins and bushings. Greased them up and within a hour the arms literally popped off both sides. See attached photos. No signs of anything binding and all looks straight. Any help would be appreciated! Please ask for anymore details or photos....

Cat 416 c linkage problems

Cat 416 c linkage problems

Hello

Hello all. Just found this forum and wanted to say hi. I'm a home builder based in Arizona. Thanks for all your future help!

Hello

Case 580 b ck

Having a little problem with hydraulics. Replace 2 lines on rear and added hyd oil and rear won't do anything. The out riggers will go up and down and the front is acting a little crazy. Need some help. First time owning a backhoe.

Case 580 b ck

Tilt and Lift not working on Bobcat 863

Hi,
The Bobcat in question is an 863F manufactured in December 1998.
It has about 2,400 hours.

Today after warming it up for about 10 minutes in 29°F I began by removing the bucket to attach a tree boom.
Before I could hook up the boom, the tilt and lift stopped working.
I turned the engine off.

5 Minutes later I started it up again and the tilt and lift functions worked again, for about 20 seconds.
turned it off again and checked battery connection.
(installed brand new battery...

Tilt and Lift not working on Bobcat 863

Tilt and Lift not working on Bobcat 863

Skyjack 3219 Scissor Lift Locks Up: Won't Drive or Lift

Help!! We have a Skyjack SJIII 3219 scissor lift (Shipped 08/06) that I need help with troubleshooting. After the lift sits overnight I go to drive or raise the platform and the lift will work fine for a couple minutes and then I start having problems. The brake may not release for reverse but it will for forward or it may not release for either forward or reverse and the platform usually won’t raise again. The pump motor makes a bogging sound like a valve is not opening. Any advice on...

Skyjack 3219 Scissor Lift Locks Up: Won't Drive or Lift

Skyjack 3219 Scissor Lift Locks Up: Won't Drive or Lift

HITACHI EX 200

I have a 1990 hitachi ex 200 had a guy come over and replace a hydrolic pump for me and he never finished i put it back together myself but in the process got some lines crossed somewhere and my joystick and drive arms are crossed does anyone have a diagram to show me where the lines go thank u very much. Kenneth.

HITACHI EX 200

JD 490E computer code reading

I have a John Deere 490E excavator with two computer modules, each with a red lens to flash error codes. I also have the technical repair manual TM1505. I have found nothing in it to tell me how to read the computer error codes or what they mean. Does anyone know where I can find that information?

JD 490E computer code reading

Hi Everybody

Hi,
This is Andrea, Working in brothers Gas as an industrials analyst.

Hi Everybody

Thumb problems KX-71

View attachment 94415 View attachment 94416
Hello.
Im having problems with my thumb.
It has good clamping pressure and speed, but the return is week to non existant. I swaped the hoses and the problem followed,
as in the clamping pressure was nil and the return was fast. Way to fast.
In the pics you can see the block that the hoses attach to. The larger pipe feeds the bottom of the cylinder.
The thumb will creep down after I shut off the machine.
Any ideas guys?
Jason

Thumb problems KX-71

D60-6 Cummins NH 200 Running On

Gday all. Just wondering if any of you have come across a Cummins NH220 running on after shutdown (can be up to 30 seconds). Was fine before full engine over haul. Has a recon PT pump and new injectors. The overhead adjustments have been checked several times and all good, new filters and fuel, fuel float tank disassembled cleaned and inspected. On shut down with fuel return removed theres a large amount of spluttering fuel vapour not a solid stream of fuel as there should be. Obviously...

D60-6 Cummins NH 200 Running On

D60-6 Cummins NH 200 Running On

580c trans fluid

what oil is required for the 580c trans? ive read gear oil on other site, doesn't sound rite,im thinking trans/hydro

580c trans fluid

case 580d backhoe bucket ear/pin measurements

Hi guys I need to buy a trench bucket for my 580d issue is I'm having issues finding one in Australia. and since the backhoe is 3 hours away at my block of land I don't really want to drive 3 hours one way to measure bucket.
any one know the measurements to save me driving all the way?
Thanks
ben

case 580d backhoe bucket ear/pin measurements

What Kinds of Tasks Require a Mini Excavator?

There are many kinds of tasks that can be accomplished with a mini excavator. This small heavy equipment is perfect for projects around the house or garden or for construction projects. Even though mini excavators are smaller than other kinds of equipment, they are powerful and can handle a variety of jobs.


Some projects that mini excavators...

What Kinds of Tasks Require a Mini Excavator?

What Kinds of Tasks Require a Mini Excavator?

Hydraulic Clamp/Thumb - Bobcat 325

I’d been having some difficulty getting a new aftermarket thumb to work on my 1998 Bobcat 325 mini-ex. However, I finally have the whole thing working perfectly!

Along the way, I purchased the Operation and Maintenance Manual. On Page 83, there is one small note in the manual that says that the use of the thumb “Requires” the use of port relief valves in the auxiliary valve circuit, but the whole thing is working perfectly. So, could anyone help? Am I going to damage something by using...

Hydraulic Clamp/Thumb - Bobcat 325

Hydraulic Clamp/Thumb - Bobcat 325

Mini Ex Questions - Volvo EC20B

Just purchased a used Volvo mini-excavator and have put 30 hrs on it and have a few questions being new to heavy equipment.
I have been greasing the zerks every 10-15 hrs that I can find but other then the track tension, I can't find anywhere to lube the track rollers/ sprocket and they are getting noisy. Is there a need to lube these parts or is it just a matter of blasting them off with a hose to keep them free of dirt and squeaks?
Also, when engaging the high speed (haha) the excavator...

Mini Ex Questions - Volvo EC20B

Mini Ex Questions - Volvo EC20B

Caterpillar 615 scraper

Hi fellas i have a 615 with axle suspension not working at all. Have had recharged just wondering could it be a pump problem.

Caterpillar 615 scraper

Climax line boring bar for sale BB1149 (BB5000 with 2" bore), Mics, OTC press, turnkey $40k

RDU, Feed unit, motor, spare motor, 4 climax bearings, 4 extra support bearings, small bore kit with 3 bearings, 2" bars- 4,5,6,7,9,13 1.25" bars- 4,5,6,9. Bar set up pilots and cones. Flycutters up to 14", Mics 0-16" digital calipers 0-18", tool bits and grinder. OTC 10K psi pump with 55 ton hollow ram, bearing pullers. Service truck bar storage compartment, Knack box, plus more.

please look up...

Climax line boring bar for sale BB1149 (BB5000 with 2" bore), Mics, OTC press, turnkey $40k

Climax line boring bar for sale BB1149 (BB5000 with 2" bore), Mics, OTC press, turnkey $40k

1969 580CK - Broken Transmission Gears

Hi everyone, I've been lurking around the forum for some time now but am hoping you guys can help me with my latest problem.

I recently purchased a 1969 580CK diesel with a power shuttle and 4 speed. I bought this machine not running with a broken ring gear on the flywheel. Over the course of a few weekends, I managed to split the tractor and replace the ring gear successfully. This is my first piece of heavy equipment so I learned a lot along the way.

Once the tractor was running I went...

1969 580CK - Broken Transmission Gears

1969 580CK - Broken Transmission Gears

Where is Nige????

Have not seen him post lately. Hope He is ok and will post again soon. Always enjoy his knowledge about everything CAT.

Where is Nige????

Komatsu Pc50 bucket size

I have a Komatsu Pc50, it's around 11k lb machine. It had a 24" bucket that is pretty torn up.

I found a nice 30" bucket, but not sure if that is going to be to big for the machine.

Any advice?

Thanks

Komatsu Pc50 bucket size

General Pricing Help Needed

I had posted a thread with questions regarding some grading I'm looking at having done, in the scraper section / sub forum, but figured a pricing question might get some more traction in the general forum. I'm completely new to grading/leveling/etc, and just trying to learn as much as I can about it now.

I was able to get some help and some questions answered in that thread, but...was hoping a couple folks could give me some feedback on what pricing might be for what I'm looking to get...

General Pricing Help Needed

General Pricing Help Needed

Wacker Neuson Skid Steer

Check this out, I saw it driving down the highway yesterday in Wisconsin...I know about the the small Wacker equipment and I have seen their excavators but never seen one of these. Do you think these are coming to the US??? Anyone know anything?

Wacker Neuson Skid Steer

Think big student!!!!

Hello everyone,

I actually joined this sight some time ago however never even came back to visit until now. I recently remembered about this sight and thought that it would be a good idea to come back and start being active. My goal here is to strengthen my knowledge of Heavy Equipment to make me a better Technician. I am currently working as a Dealer Technician in the San Diego Area. I am also part of an apprentice program called Think Big where we a trained in Caterpillar Machines...

Think big student!!!!

Think big student!!!!

Spanner wrench for Hyd Cylinders

I need to put new seals in the tilt cylinders on my A300. What kind or brand of spanner wrench do you guys use?

Spanner wrench for Hyd Cylinders

SVL75 - Shattered Door Window

Dayum,
Using grapple to clear some cut mesquite brush and BAM, piece of mesquite shot up like it came out of a rifle and shattered the door in a million pieces. Certainly got my attention! New unit, just 35 hours.
I imagine it's not going to be cheap to replace the thing. Problem is what's going to keep it from happening again? I wonder if they offer an option with ballistic glass

SVL75 - Shattered Door Window