KOMATSU HD605-7EO blower motor

mercredi 31 janvier 2018

Does any one have any options for HD605 rigid haul truck blower motor for cab? Needing to replace however priced through komatsu and they only sell the complete assy for $750 when all that's needed is the electric motor. Ive tried aftermarket but it will not easily match to OEM housing. Any options?

KOMATSU HD605-7EO blower motor

'93 Deere 310D front differential locked and cant unlock

Hi all,
Ive owned this backhoe loader for a few years, its been a great work horse around the farm. I was out clearing some land, it was wet, muddy and cold out, and I engaged MFWD to help climb out of the mud. I turned it off, the indicator on the light went off, but I still had a very difficult time turning. I had the same thing happen once before when spreading millings on the road, it was a dry day but also just below freezing temps. That time I was able to get the front unlocked by...

'93 Deere 310D front differential locked and cant unlock

'93 Deere 310D front differential locked and cant unlock

988G 988H hydraulic hoist and curl

Have two 988H with that no longer hoist boom and curl bucket at same time. both are BXY prefix. Both issues occurred with in the past month. pump will maintain 4000 psi. boom and bucket sensor calibrations have been completed. all pins are tight and sensors are not seeing any slop (unexpected movement) Does any one have any ideas what would cause the machine to NOT perform two functions at once? The boom will raise with no issues but as soon as you attempt to curl the bucket back...

988G 988H hydraulic hoist and curl

988G 988H hydraulic hoist and curl

Case 580K dead instrument cluster

I have a more of a beginner mechanic question, I have a phase 3 580k thats new to me, and by new I mean I bought it, worked it for 2 days and almost every cylinder on the machine blew out under load and other issues that caused it to be in the shop for 4 months as of now. The entire instrument cluster was dead, and I asked the tech to look at it to find out what might be shorting it out (I absolutely hate running machines with dead gauges and not knowing what its doing, call it a pet peeve...

Case 580K dead instrument cluster

Case 580K dead instrument cluster

Loader spool stuck

On my Thomas Pro Tough 1700 skid steer the loader arms will go up, but not down. The cable from the foot pedal is operational. I then checked the solenoid that locks out the spool and it works. I re-greased the detent assembly thinking it was hanging up.
Nothing worked so I took the spool out of the valve body. I had to pry it up with a board to get it unstuck. It seems like hydraulic pressure was keeping it frozen. I took it out expecting it to be galled or damaged, but it looks like new...

Loader spool stuck

Loader spool stuck

D9h bevel gear shaft.

Hello everyone,
So we're working on a d9h that had a steering clutch non release issue. What had happened was the outer hub walked loose and the nut and the lock bold ended up in the basket. When the clutch was applied it caused the clutch to smash and jam.
The last owner pulled the outer shaft and fixed and pressed a new hub on. They changed the piston seals but didn't do the swivel seals behind the hub.

When we got to the machine we tested it and found the swive seals were gone. We...

D9h bevel gear shaft.

D9h bevel gear shaft.

Lowboy Trailer Recommendations? Kaufman?

I am in the market for a lowboy trailer to haul my D6 dozer, Prentice 2864, and monster truck (Walking Tall). I do not use heavy equipment for a living but do want to be able to haul it when needed. I will not be hauling long distances--the furthest would likely be 50 miles at a given time. I will also be using the trailer relatively infrequently, probably just once a month of so (I want to buy one though--I do not want to hire folks to carry things). I was going to buy a used trailer but...

Lowboy Trailer Recommendations? Kaufman?

Lowboy Trailer Recommendations? Kaufman?

555D slow hydraulics

Looked at this machine today: 555D with slow hydraulics. Fluid is full on both sticks. Bucket and hoe are jerky and slow. Filters or strainer. Can not read much of the data tag the parts guy wanted. Anybody have any input on that? Filter and strainer locations? Will get a tire back on it and move it to better working ground tomorrow. Any experienced input will be appreciated.

555D slow hydraulics

WW2 Iron

i’ve had some free time for surfing lately and read up on some of the innovations of ww2 designers. I guess the weight alone would qualify some of it as HEAVY Equipment. Look at a Soviet V12 diesel: aluminum block iirc, one bank had a longer stroke, pre-start oiling system, and 38L displacement. The most common Sherman tank model had an air-cooled aircraft radial engine. And aircraft engines using (or trying to use) turbos, superchargers, direct injection, multi port fuel injection, and...

WW2 Iron

WW2 Iron

Barko 270 harvester

Has anyone here had any experience with one?
I just had one quoted with a Southstar QS500 head.

Barko 270 harvester

Link belt htc 8620 boom problem

Our company just purchased this crane and the first job we are at the boom has a malfunction. I was telescoping it out and the cylinder had a error. I had to put it in manual mode to scope it back in. After it was scoped in I tried to scope it back out normally and on the last boom section the cylinder isn't retracting enough to latch correctly. It is only going to 10.000 instead of 1.000 which is the correct number. Any help on this would be much appreciated.

Thanks, Tony

Link belt htc 8620 boom problem

Forklift Certification...

I just got a mailer from United Rentals. They are offering a Lull Forklift Certification class, $250 per person. In the letter it states that "as of 12/1/99 Operators must be OSHA compliant, it's the law" Can anyone tell me what this means? I know lots of Lull operators that have not had any formal training classes or certifications. What does it mean to be OSHA compliant? I am in CT btw, which I know has some different laws regarding equipment operation, etc. vs. states like MA.

Forklift Certification...

cat roller seized engine valve

im puzzled got a major problem,i just overhauled a cat cs 533 e engine 3054(perkins by the way)
put in new pistons,bearing etc,after some good hours of running in went for a test full throttle with vibration on and it starts missing about 20 mins later.
finally opened the valve cover and found a push rod had popped out because an inlet valve number one had siezed.

putting in a new valve and all the valve guides although they are fine.
anyone had such an issue coz i cant figure out why this...

cat roller seized engine valve

cat roller seized engine valve

Cat 936e transmission

My cat 936e wheel loader transmission pressure is low. I have changed the transmission pump but still it is low. It reads 80 instead of 400. Before i changed the transmission as the gears was automatically changing to neutral. And now the pressure is low.

Cat 936e transmission

Cat 936e transmission

My cat 936e wheel loader transmission pressure is low. I have changed the transmission pump but still it is low. It reads 80 instead of 400. Before i changed the transmission as the gears was automatically changing to neutral. And now the pressure is low.

Cat 936e transmission

CASE 440CT Track Tensioner Valve & Grease Zerk

Grease was leaking past and through my grease zerk at the end of my track tensioner valve. I replaced it several times, but that didn't fix it. Then I replaced my entire track tensioner valve, which came with a new grease zerk installed too. The new valve leaks grease past and through the grease zerk just the same as the old one.

I had recently done some work that I had to remove my track for, and I removed my old track tensioner valve completely before I performed the work. Is there a...

CASE 440CT Track Tensioner Valve & Grease Zerk

CASE 440CT Track Tensioner Valve & Grease Zerk

CAT 216B with Perkins 3024 Failure

First time posting on this great site. I have a 2006 216b that unfortunately experienced a catastrophic engine failure at only 346 hours. Even though its a 2006 it has very low hours. I was working the machine which developed an unusual slight ticking sound which quickly developed to a hard knock in seconds resulting in engine stall before I could shut down. From what I can gauge from a quick (disheartening) inspection, I threw a rod off of the crank which piled against the block in the...

CAT 216B with Perkins 3024 Failure

CAT 216B with Perkins 3024 Failure

Td 7 Injection pump needed

Looking for a fuel injection pump for a International Bulldozer TD7 Non turbo
Motor: D239
The tag says:
011 45102993
0460 304 226
VA4/10H12500R89/1

Td 7 Injection pump needed

does anyone use a mtl

so I know I build the damn skid steers and I know what makes what but is anyone buying mtl loaders or seeing any around because I'm not I mostly just see the ctl.

does anyone use a mtl

looking at a koehring 6625

well whats the good and bad. This will be my first excavator, it is very reasonably priced. Mainly just be doing house demos, loading clay and doing some light digging (basements ect.) Any pros and cons would be a plus, i have looked it over and it looks pretty clean, no cracks or welds, undercarriage decent but will need drive sprockets pretty quick and tracks are about out of adjustment and bucket will not curl but does dump which just started happening so im guessing just stuck hyd spool...

looking at a koehring 6625

looking at a koehring 6625

Pacific trucks in the logging industy

Post pictures of Pacific trucks in the logging industry.:canada I thought I better close the gap/ring of huge logging trucks so all makes are represented. Here are some LLL P16 models at Port McNeill.

Pacific trucks in the logging industy

Does Cat 941B track/shoe fit 941?

I dont know if this is too broad of a question and if there is more info needed to answer it or if some of you seasoned guys will be laughing at me at even posing these questions but.....

Can anyone tell me if a 941B track and/or shoes will fit a 941?
Is this compatibility based on the serial numbers at all?

the shoes on my 941 are pretty worn and I'm looking at a parts machine that has good shoes. parts machine does run/move.

Is it easier to just swap out tracks from one machine to the...

Does Cat 941B track/shoe fit 941?

Does Cat 941B track/shoe fit 941?

Made a door myself

Hi everyone
I just wanted to show you how I did.
Cheap, simple and rugged solution and I used:
14 mm lexan
Some modified door hinges
Seal
Cost 190 USD

View attachment 177389

Made a door myself

Leak sealers

mardi 30 janvier 2018

My 330 ford is leaking water out the back of one head i think about half a gallon on a 200 mile trip. I would like to weight till may to replace it. I thought about some sealer but it has a new rad and heater core. Has any one ever had a problem with stop leak? I have used bars before and it worked but i didnt care alot about the future of the vehical.

Leak sealers

Deere vs cat wheel loader

Getting to demo 544k loader against my 928g tomorrow. Sales man biggest selling point is dif lock. I bucked into a sand pile real quick and wasn't impressed as I couldn't lift a bucket full while pushing against it like the 10,000 hr cat. Anyone else run the same demo or run a deere?

Deere vs cat wheel loader

Volvo EC15B more problems

Volvo EC15B XTV older machine but low hours 600ish

Starts & runs for a couple seconds then instantly shuts off.
If i hold the key in start position is stays running until i let off, then dies right away.

Most of what ive read says that it is an electrical issue? Solenoid perhaps? Relays?

Recently changed my fuel filters, not sure if an air lock could do that....ive already cracked the injectors trying to bleed the motor of any air locks

ive checked the battery cables, all fuses are good,...

Volvo EC15B more problems

Volvo EC15B more problems

Komatsu GD655-6

I've asked about Komatsu graders in the past, but all the machines have newer series out now.
So I wanted to ask again...has anyone run one of these new Komatsu's? Most of the talk I see is about Deere and Cat.
How would these compare? In the brochure pics, visibility looks good. And they come with an awesome standard warranty and service plan.
http://www.komatsuamerica.com/equipment/motorgrader/grader/gd655-6 View attachment 177380 View attachment 177381

I don't run grader, but...

Komatsu GD655-6

Komatsu GD655-6

Memories for us old truckers

Oxbow started this thread at the HTF forum.

Truck Shop



Memories for us old truckers

Genie Z60/34 boom lift

I have here a Genie Z60/34 boom lift serial number Z60-3551 with 2370 hours on it. That somedays the swing is good in either directions .Other days it so slow in either directions.Anyone have any ideas.

Genie Z60/34 boom lift

Buckeye Wheel Trencher model 307 Transmission problems

Need to find the main transmission for a model 307 buckeye trencher. Something has let loose in the transmission and cracked the case. It hasn't been pulled yet just trying to locate one.

Buckeye Wheel Trencher model 307 Transmission problems

Junkyard's work thread.....maybe haha

While I don't do stuff near as cool as most of you I figured I'd start showing what I do on a regular basis. I'd like to name my favorites on here, but being a father of five I've learned to avoid hurt feelings haha. I manage equipment for a small excavating company. We run a D11N, D7R, D5G, D65, Steiger 485 HD with two 19 yard pans, two 210 Linkbelts, 110 SD roller, champion grader, 627B and a couple water trucks. I do all the service work and 99% of the repairs. Just did steering...

Junkyard's work thread.....maybe haha

Junkyard's work thread.....maybe haha

in search of a used mini

Hey there,

Finally found a site that I can bounce some ideas off of! ya!
New to the site, and the world of excavators, I bought a piece of property and would like to have a machine to do some work with. So many questions! I guess first of all, i am thinking of size, I rented a JD60 and that seemed to be ideal for what I need, but been pulled to the JD, bobcat, hitachi.....in the 7500lb range. Not sure if i will be kicking my self if I go that small....????
My lot is all sand and...

in search of a used mini

in search of a used mini

CAT 977 been sitting for 21 years

I work for a grading contractor that owns a CAT 977 that they inherited when they bought out another grading company 30 years ago. Anyway they used the 977 very little over the first few years since they already had newer 953 and 963s. I have been told that the 977 always would fire right up after sitting for long periods even years as long as they put new batteries in it. Anyway the last time they used it was 1996 doing hurricane cleanup using the large hydraulic winch that is on the...

CAT 977 been sitting for 21 years

CAT 977 been sitting for 21 years

963 occasionally slows travel

21z 963. New engine. Machine sat for 3 years wile dead beat mechanic installed new engine. I changed trans filter and oil. Occasionally the travel speed will go down to 50% or so. If I idle down and idle back up it will go back to normal for awhile, then back into slow mode. Tried changing filter again, no change. It is a napa filter. Got a filter from cat, but have not tried yet. Any ideas?

963 occasionally slows travel

Repowerguy's crane repower

View attachment 170341 Follow along ladies and gentlemen for my latest (Mis)adventure as I repower a Drott carry deck. I will take a dead Case gas motor out and fabricobble a Perkins 4.203 diesel in its place. This won't be fast as this is a side job, but please be patient with me as we move along.

Repowerguy's crane repower

Final drive on track excavator

Took apart the hydraulic side of the final drive on my mini excavator to examine a cracking noise. The noise was likely coming from the main bearing side. Anyhow, everything went back as it came apart but the drive does not turn now - it did beforehand. Is there a priming mechanism , presumably they dont air lock? Anyone know any likely reasons why it won't turn on reassembly?

Final drive on track excavator

955 Bucket Repair

Buddy was using my loader and was trying to dig some large rocks out. Now the lower lip has been torn. Also has some cracks along the back cutting edge. Took it to a welding place which seem to have trouble coming up with a price to fix. Asked what was the max, and he even had trouble with that.

Found a bucket on another loader which had caught on fire a few years ago, but it is a smaller bucket then mine (2 yard). I can weld, only issue is I'm not great at it. Appears it will need a...

955 Bucket Repair

955 Bucket Repair

Deere J model changes question

Hello all,

I am upgrading my 550H, which i currently use for general grading, and finish grades on smaller home lots for a builder i work for.

I love the dozer, and I am only upgrading to another deere machine, either 550 or 650 but a J model.

In my searches, I have noticed a few changes seemed to have happened over the years.

Looks to me 05-07 had a different dash, and I'm guessing different computer controls?

the 08 and newer seem to have the dash, where you can control the...

Deere J model changes question

Deere J model changes question

what side to run your mine whip???

currently setting up my service pickup for working on mine sites, what side are you suppose to run the whip on? i have seen them on the left side in the USA and the right side up in CAD?

what side to run your mine whip???

Loader Project Today

Today after doing snow removal at our yard, while the loader & dump truck were still warmed up, we moved the machine over to our local kennel ladies place where we take our dog to board when travelling & did a little driveway extension for her that she needs done to get a concrete truck backed in for a building addition that she needs done. The driveway extension will be permanent after the project has been completed. Perhaps we can go back in the spring & dress the edges with soil for her...

Loader Project Today

Loader Project Today

Service Manual Trading Post

If you need a manual post what you need. (PDF Format)

Maybe someone can help.

I have a lot of deere manuals and i need some caterpillar: specifically 420D

Service Manual Trading Post

Komatsu D-65 Dozer good and bad?

Looking at a 80s Komatsu D65P-8.
Tell me what's good about them, or if there are common issues with them. Thank you

Komatsu D-65 Dozer good and bad?

Finding qualified help

Is any one else having a hard time finding CDL Drivers or Experienced equipment operators? This year the pool of talent seems to be getting smaller, with many old timers retiring, there do not seem to be many young guys or girls getting into the industry.

Is this an industry wide problem or is it just in New England?

If you have experienced this what have you done to encourage new comers to the industry?

Sorry if this thread already exists but I did not see it.

Finding qualified help

halla questions/help please

Ive searched on here for info on halla excvators, we bought a he220 and would like to find some mauels for it and possibly a place for parts new/used. Any help would be appreciated. Thanks

halla questions/help please

Service truck for sale

If anyone is interested our service truck is for sale. If no one takes the kit it will be sold at auction in Orlando in February. 2008 Pete 335, Paccar (Cummins) 8.3L, seems I recall it's around 280ish hp, 6 speed Allison auto, 3.75 rear axle, a little over 91K miles. We've had the truck a little over 5 years, turbo and EGR have been replaced. This past summer the catalyst was replaced and DPF cleaned as well as all 6 injectors replaced. Truck is in excellent shape, cab interior is...

Service truck for sale

Service truck for sale

http://ift.tt/2GwPmLt

lunar eclipse Live
lunar eclipse
Lunar Eclipse 2018 Australia
lunar eclipse Live Stream
lunar eclipse Online
lunar eclipse Live Stream
2018 lunar eclipse
Super Blue Moon
Blood Moon
Blue Moon
lunar eclipse 2018
lunar eclipse 2018 Live Online
lunar eclipse Date
lunar eclipse Start Time
https://livetvonlinegame.com/lunar-eclipse-live
https://livetvonlinegame.com/lunar-eclipse-live
https://livetvonlinegame.com/lunar-eclipse-live...


https://livetvonlinegame.com/super-blue-blood-moon

http://ift.tt/2GwPmLt

http://ift.tt/2DO1zd0

lunar eclipse Live
lunar eclipse
Lunar Eclipse 2018 Australia
lunar eclipse Live Stream
lunar eclipse Online
lunar eclipse Live Stream
2018 lunar eclipse
Super Blue Moon
Blood Moon
Blue Moon
lunar eclipse 2018
lunar eclipse 2018 Live Online
lunar eclipse Date
lunar eclipse Start Time
https://livetvonlinegame.com/lunar-eclipse-live
https://livetvonlinegame.com/lunar-eclipse-live
https://livetvonlinegame.com/lunar-eclipse-live...


https://livetvonlinegame.com/lunar-eclipse-live

http://ift.tt/2DO1zd0

Buying a used 953, B or C, anything special to watch out for?

Hi!

I'm looking on buying a used 953, C-series or older. Is there anything special to look after? What are the typical problems and what is expensive to replace (besides UC).
I saw a 953C that is really cheap, but with UC quite totally toasted and almost 20000hours on the meter. Otherwise the machine looks really good, stock painting and stickers etc, cab in nice shape, soo I could assume someone took care of it. But hard to tell if transmission is OK and how many hours do you make on a...

Buying a used 953, B or C, anything special to watch out for?

Buying a used 953, B or C, anything special to watch out for?

http://ift.tt/2DO1zd0

lunar eclipse Live
lunar eclipse
Lunar Eclipse 2018 Australia
lunar eclipse Live Stream
lunar eclipse Online
lunar eclipse Live Stream
2018 lunar eclipse
Super Blue Moon
Blood Moon
Blue Moon
lunar eclipse 2018
lunar eclipse 2018 Live Online
lunar eclipse Date
lunar eclipse Start Time
https://livetvonlinegame.com/lunar-eclipse-live
https://livetvonlinegame.com/lunar-eclipse-live
https://livetvonlinegame.com/lunar-eclipse-live...


https://livetvonlinegame.com/lunar-eclipse-live

http://ift.tt/2DO1zd0

lunar eclipse Live

lunar eclipse Live
lunar eclipse
Lunar Eclipse 2018 Australia
lunar eclipse Live Stream
lunar eclipse Online
lunar eclipse Live Stream
2018 lunar eclipse
Super Blue Moon
Blood Moon
Blue Moon
lunar eclipse 2018
lunar eclipse 2018 Live Online
lunar eclipse Date
lunar eclipse Start Time
https://livetvonlinegame.com/lunar-eclipse-live
https://livetvonlinegame.com/lunar-eclipse-live
https://livetvonlinegame.com/lunar-eclipse-live...


lunar eclipse Live

lunar eclipse Live

Late 90s 753 Bobcat lift/tilt problem

I have a late 90s 753, put a new ignition in it. Now the bucket tilted all the way out and cylinder will not come back in , and arms will lift but to lower pedal has to be pushed to float position. lights are all on except seat light is blinking? any ideas?

Late 90s 753 Bobcat lift/tilt problem

Loaders, Limbers and Roadbuilders.

We seem to have a thread for everything else, might as well combined all makes of forestry excavators, road builders, processors and loaders to one thread.

Loaders, Limbers and Roadbuilders.

Walker's work doing's

Brand me frontier brush hog wrecked in 1hr repaired in 4 View attachment 157595 View attachment 157596

Walker's work doing's

New ELD laws

Just looking for some clear info on the new ELD stuff they are putting in place. I have heard alot about it and don't know what all is true.

New ELD laws

New business

Ok ya'll I am in the process of planning to go legit with a new business. I've been looking into starting an LLC to protect myself and what little assets I have but was wondering if there are any other options.

A little background, It's is not equipment related but I train horses on the side and my wife trains and gives lessons, she has now started giving lessons on one of our horses. It seems as though we caught a break and now it is really starting to take off and we are starting to get...

New business

New business

Deere 959K, hotsaw to processor. Feasable?

In order to reduce our outside costs and streamline our productivity I am considering putting a waratah 624 on a John Deere 959k buncher. We would like to put the buncher head back on when it is needed to cut a unit and then put the processing head back on to process under the yarder. What all would need to be done aside from the obvious hanging brackets and piping on the Boom?

Deere 959K, hotsaw to processor. Feasable?

MICHIGAN Loader 175B - Steering Pump Assy for sale.

Available Steering Pump Assy code 2514128
Genuine Part - New Article in stock
Application : CLARK MICHIGAN 175B and CLARK MICHIGAN 175C
Price : 1.500,00 Eur + spedition
Last Piece !!

MICHIGAN Loader 175B - Steering Pump Assy for sale.

http://ift.tt/2FvbFQn

lunar eclipse
lunar eclipse Live
lunar eclipse Online
lunar eclipse Live Stream
2018 lunar eclipse
Super Blue Moon
Blood Moon
lunar eclipse 2018
lunar eclipse 2018 Live Online
lunar eclipse Date
lunar eclipse Start Time
https://livetvstreamgame.com/lunar-eclipse
https://livetvstreamgame.com/lunar-eclipse
https://livetvstreamgame.com/lunar-eclipse
https://livetvstreamgame.com/lunar-eclipse
https://livetvstreamgame.com/lunar-eclipse...


https://livetvstreamgame.com/lunar-eclipse

http://ift.tt/2FvbFQn

After work, hobbies & life after the logs are loaded!

lundi 29 janvier 2018

At the suggestion of a member wiser than myself, here is a thread for us to post our after hours hobbies & pastimes.

Here are a few of mine. View attachment 177339

After work, hobbies & life after the logs are loaded!

2003 Case 40XT Sticky Control Issue and Fan Question

2003 Case 40XT with 940 hours. Bought used and have put 60 hours on it with little trouble. Operated perfect and smooth when parked 6 weeks ago and now the right joystick for forward and reverse has a catch or is sticky. The left side is buttery smooth as was the right side before it was parked (central Ohio) cold temps was stored in a non insulated shed.

The weather warmed up and I was bringing it up to the garage to go ahead and knock out the 1000 hr hydro service and the right joystick...

2003 Case 40XT Sticky Control Issue and Fan Question

2003 Case 40XT Sticky Control Issue and Fan Question

Allis Chalmers grader with electric brakes

Got a call from a guy that has an A-C grader with Wagner Electric brakes. Never heard of that and not finding much info... Any of you members deal with them? I haven't looked at it yet, 125 miles away.

Allis Chalmers grader with electric brakes

Horton fan cagenut

I am going to replace the bearing and stuff in a Horton clutch and it says i need a cagenut 17310 is it lefthand thread?

Horton fan cagenut

And so it begins. (The never-ending flow of cash)

Figured I'd start my own thead for the shop project. Get started with some pics of the iron and footings.
Enjoy.

And so it begins. (The never-ending flow of cash)

Mack END673 headgasket(s)

Hello and happy 2018 to H.E.F. crowd!
I have been tinkering with a 1962 B-61 six wheeler with a quadruplex and END673. This truck has sat idle for around 25 years giving lots of time for the mice to move into the cylinder head and fill it with filth. The original idea (mine) was to clean the top up, pull injectors, put back in rebuilt injectors with fresh copper rings and crank it up. I made the decision to pull the head because the rockers and push rods were so caked with mouse filth I...

Mack END673 headgasket(s)

Mack END673 headgasket(s)

New Kubota SVL95-2

Its a thing of beauty...Compared to my beat up Kobelco and my prehistoric Case 1150B

Anyway, I plan to work it at my farm for maybe a month, then ship the thing to Africa where I am putting together another farm. MY US Spec machine has that DPF/DEF tree-hugger junk on it. I understand that I am supposed to do my part to keep mechanics in business and shops alive with the continuous service calls fixing that useless junk, but there are no such things where this little machine is headed. I am...

New Kubota SVL95-2

New Kubota SVL95-2

Sarge, (Case 1150B) will not lift loader past level!

OK, my 1150 loader won't lift a bucket of dirt. In fact it will barely lift the weight of the loader. Now this happened pretty much all at once. I was working a big pile of dirt that I had heaped up with the Kobelco pulling one load at a time and using it to track in the dam of a new pond. I pull into the pile low gear and raise and curl, just like a thousand other times, but this time, with a bull bucket, the thing won't lift anything!
Imagine that an old Case breaking down...That is sure...

Sarge, (Case 1150B) will not lift loader past level!

Sarge, (Case 1150B) will not lift loader past level!

Deere 892 ELC Throttle problems

Can any of you old timers out there help me with my '96 Deere 892 ELC? I have had this thing for about 8 years now and it has been a good machine most of the time until this problem came up. The problem started out very simple. I would be using it right along maybe loading trucks and a driver would get out to talk to me and I would have to shut it off to hear him. When I would start it up again I would push the p button to rev it up and nothing would change. I started out just shutting the...

Deere 892 ELC Throttle problems

Deere 892 ELC Throttle problems

Self loader work

How does one go about finding work for a self loader in Washington state?

Self loader work

Caterpillar 950GC

Is a 950GC just a more simplified version of a K or M model. Also, my understanding is that it is only tier 3, is that correct? Thanks

Caterpillar 950GC

Massachusetts 4E license

I currently have a 2A but need to get my 4E. Can anyone give me a heads up what might be on the test? I have reviewed the CMR's and MGL's but there is nothing that I saw that was specific to a catch basin truck.

Any help would be great

Massachusetts 4E license

Cleaning inside dozer frame?

Hey again,

I have a D6H with years and years of accumulated oily dirt covering everything under the floor/seat. What is the best way to clean all the crud off.

Products or methods?

Thanks,

Cleaning inside dozer frame?

backhoe VS mini excavator production questions

Im an owner operator of a cat 420d for about 10 years now. Back in April I bought a Kubota u25 and I have seen the light. I am now seriously considering selling my backhoe to get a 6 ton mini and a CTL. I work almost exclusively for a foundation contractor and the scope of the work we do has changed so drastically in the last few years I have almost no space to run the backhoe. I am wondering if anyone could put some kind of percentage number on the two machines vs. my backhoe. im thinking...

backhoe VS mini excavator production questions

backhoe VS mini excavator production questions

Favorite phrases you use

Everyone has a favorite saying or two that they use on a regular basis. Here are a few of mine

1- 90% of the time the enemy of good is better.
2- Never judge a mans success by the number of presidents in his wallet.
3- If you would hang up that welfare radio and look at your gauges once in a while you would have less crap in
your crap sandwich each day and turn off that radio talk show garbage too.

Truck Shop

Favorite phrases you use

Cat IT28B OIl Leaking From Starter

Ive got a Cat IT28B (serial 1HF00904) that has oil leaking from the starter gasket. I’ve been doing some reading and from what I’ve read usually that gasket will leak if the tranny fluid is overfilled or a plugged breather. My question is it isn’t a small leak. At idle there is a steady stream of oil coming out. It is clear like hydraulic and the tranny level is just about empty. The leak went from not leaking at all to this steady steam instantly. (It didn’t start with a drip and get...

Cat IT28B OIl Leaking From Starter

Cat IT28B OIl Leaking From Starter

621D hydraulic problems

We have a 621D that keeps loosing hydraulic functions ( all loader controls and steering ) this problem is intermittent and happens more often when cold. typically goes away after restarting the machine a few times and will usually function fine the rest of the day but not always. any help would be appreciated thanks in advance.

621D hydraulic problems

Volvo A40 BM

I'm looking at a used Volvo A40 2000 year model I believe and the battery voltage light is on and the stop light is flashing on the dash is these correlated with each other? The voltage at alternator and the batteries is 27 volts. So what sets the stop light off? The digital display up by the head liner don't work would that tell me what the problem is?

Volvo A40 BM

ANOTHER NEWBIE SKID STEER PURCHASE THREAD

Greetings!!!
I did a search and read a bit but thought I would also ask for input from the members here.

Considering purchase of a skid steer and I am out of the loop on good/bad years/brands of machines out there right now. I started in construction in 1976 and back then it was Bobcat with sticks and we ran the wheels off those things. I've ran most construction equipment over the years but got out of construction in 2001.
I owned a Cat 226 (used for home/residential use) for several years...

ANOTHER NEWBIE SKID STEER PURCHASE THREAD

ANOTHER NEWBIE SKID STEER PURCHASE THREAD

Crane service manual/Workshop manual I have

GROVE: AT422; RT875; GMK3050-3055-4070-4075-5100-5130-5160-5180-5220-6200-6250; RT500E to 9000E; TMS500E to 900E; RT890E; RT9130E-1&-2

KATO: SR250-V; NK250E; NK550VR; SR300L to 700L; SS500; KR25H-III

KOBELCO: Many Crawler Crane

KOMAT'SU: LW80; LW250...

KRUPP: 30GMT; 70GMT; 100GMT; KMK4080; KMK5110; KMK5120

LIEBHERR: LTM1030; LTM1040; LTM1050; LTM1060; LTM1070; LTM1130; Service_Libherr_Crane - LICCON

LINKBELT: ALL MODELS FOR WHEEL CRANE AND CRAWLER CRANE (5.6GB)

LOAD...

Crane service manual/Workshop manual I have

Crane service manual/Workshop manual I have

Best Grease for Heavy Equipment (Graders, Loaders, Dozers)

Hey,

I seen there was an older post about this but the last post was from 2014. I wanted to see what everyone views as a great grease brand for their heavy equipment and why. Thank you

Best Grease for Heavy Equipment (Graders, Loaders, Dozers)

NHL All Star Game 2018 Live

NHL All Star Game 2018 Live
NHL All Star Game Live
NHL All Star Game 2018

NHL All Star Game 2018 Live Stream
NHL All Star Game 2018 Live Online
NHL All Star Game 2018 Live free
NHL All Star Game Live Stream Online Free
2018 NHL All Star Game Live
NHL All Star Game 2018 Live Streaming
NHL All Star Game...


NHL All Star Game 2018 Live

NHL All Star Game 2018 Live

Screw type compressor problem

So I found myself in a little over my head with this one. I’ve got a Sullivan palatek screw type compressor. One day while it was running it decided to puke out a bunch of atf through compressor intake. I’m not familiar with this piece of equipment at all. Does anyone have any idea what would cause this? Thanks!

Screw type compressor problem

No throttle response on case cx160

I have no response from the throttle dial in cab. The screen is showing electrical problem. This was after I welded a crack in the the bell housing where the pump attaches to it. I small fire develop in the corner below the throttle motor and it got the throttle motor harness plug hot and melted insulation on 5 or 6 wires. I spliced and replaced those wires and still no response from dial in cab. All fuses are good and throttle motor didnt get hot and appears to b e in good shape. I noticed...

No throttle response on case cx160

No throttle response on case cx160

Places to buy used/rebuilt dozer parts?

Specifically a Komatsu dozer of 80s vintage (steering valve). I know lots of wreckers for the ag sector, but not construction

Places to buy used/rebuilt dozer parts?

Steering Issues

Komatsu D21A-6
Serial- 60028
Machine will not neutralize right track when pulling lever. Linkages from left to right appear to have the same movement and relatively close adjustment. Service manual on the way. Any ideas on this condition?

Steering Issues

The JLG 40F Boom Lift Dilemma

I started talking about my JLG 40F in 3 other forums. I needed to post at least 3 times before I was allowed to post my own thread. Sorry for the inconvenience. Here are the issues. First JLG gives no support on the E or the F series. If you go to there Manual’s down load area they are not even listed. They do list some parts though. As for service they have not returned 1 of my phone calls. I did receive an email reply from them. It was a link to there dealer and service people. All of the...

The JLG 40F Boom Lift Dilemma

The JLG 40F Boom Lift Dilemma

Dirt Pans

What size dirt pans do yall pull with your tractors and how big are the tractors. How big of a pan can I pull with a 165hp duel wheel 2wd tractor. Thanks.

Dirt Pans

Purchased 555A Ford TLB

Bought a backhoe couple weeks ago. It's a 1984 555A with 4n1 loader bucket, 15ft extendable, 24" heavy duty hoe bucket. Tach says 5242 hrs but if it's accurate they have been extremely hard hours.

The extendable dipper has been broken at the elbow joint. The repair appears rather old with no reoccurring cracks/breaks.

The hoe bucket has had cracks repaired. They too appear to be old and holding.

The 4n1 appears to have been used open at a high rate of speed. The dozer edge is bent...

Purchased 555A Ford TLB

Purchased 555A Ford TLB

http://ift.tt/2FpDcCR

NHL All Star Game

NHL All Star Game 2018

NHL All Star Game Live

NHL All Star Game Live Stream

2018 NHL All Star Game

NHL All Star Game 2018...

https://livetvstreamgame.com/nhl-all-star-game

http://ift.tt/2FpDcCR

NHL All Star Game Live

NHL All Star Game

NHL All Star Game 2018

NHL All Star Game Live

NHL All Star Game Live Stream

2018 NHL All Star Game

NHL All Star Game 2018...

NHL All Star Game Live

NHL All Star Game Live

Full Circle- Back to where I started (almost)

I'll start this here, even though it may have some thing not related (trucks, equipment, cranes, logging....). I not too fond of threads by 'ILoveMe' that are pretty much "I'm sorry, I can't hear you over the sound of my own awesomeness". So if nobody is interested believe me when I say I'll understand. But, yeah, I've done a lot of really interesting & varied stuff over my career and I'm looking forward to some really cool things coming up. Ouch, my arm. Patting yourself on the back...

Full Circle- Back to where I started (almost)

Full Circle- Back to where I started (almost)

Tilcon Gammino logo

does anyone have a picture of the Tilcon Gammino logo?

Tilcon Gammino logo

Clark TA 12

Hi guys would anyone have a workshop manual for a CLARK TA12 FORKLIFT transmission please????

Clark TA 12

Training - CAT789C & D - CAT 994F - Train the Trainer

Hi all! I'm looking for a Train the Trainer course for Haul Truck CAT789C & D and WheelLoader CAT 994F preferable in Spanish. please do not hesitate to contact me at a_zeta@hotmail.com

Training - CAT789C & D - CAT 994F - Train the Trainer

Cat 262D E459-2 code

DTB01483
1665 hours

Checking and cleaning grounds. Found harness to air sensor near air cleaner laying on turbo, repaired melted wiring.
Is this motor supposed to be a wet flywheel housing? Pulled crank sensor and was soaked with oil.
No service book and no Cat ET
On the status screen, I'm not seeing any cranking rpm
I suspect a bad ECM
Relatively new here but been reading for a while, I'll do an intro post soon.
Thx
Andrew

Cat 262D E459-2 code

Bucket hydraulic flow rate

Hai guys. I m currently planning to install thumb for my hitachi zx30u-2( similar to deere 35d or 35g), anyone know the flow rate for bucket line ? Since i planning to use diverter solenoid valve to tap on the bucket line... The diverter valve on sell at ebay site got 2 option listed which are 13gpm and 24gpm...

Bucket hydraulic flow rate

F450... as a pick up

dimanche 28 janvier 2018

So I’m considering trading my 16 F350 single rear wheel in against a similar spec 16 F450. Both have the same mileage.
On paper the 450 is better as I’ll be paying less interest and get an extra year of warranty.
I’ve recently upgraded my trailer to a pre owned tag along trail king w/ tandem duals as my tandem single wheel trailer was constantly on weight limit, as was my F350. I tow occasionally maybe a few times a month, often in or through mountian regions.
Has anyone out there hot or...

F450... as a pick up

F450... as a pick up

331e thumb

I’ve got a 331e with an extended-a-hoe I want to put a thumb on it has anyone ever seen this done?

331e thumb

The Loggers Library

Books,monthly publications and such,theres a lot of good reads out there,that many have never heard of,bring them here!

The Loggers Library

Komatsu D31A-17 Transmission problems

Recently snagged a D31A-17 at a local auction. Sadly I got it home and was only able to push over a few stumps before the transmission lost all movement forward and reverse. Thanks to the guys here I was able to see the problem was most likely the strainer plugged so I dumped the fluid and removed strainer and it was just absolutely full of metal. Lots of metal sludge in the bottom of trans, didn't look like it had even been cleaned out and didnt appear to be fresh. I cleaned it all out and...

Komatsu D31A-17 Transmission problems

Komatsu D31A-17 Transmission problems

Is it possible?

I'm hoping it's possible to purchase an adapter plate for the front end of my Case 570 LXT so I can rent and quickly attach any standard Bobcat attachment instead of my front bucket. If so....

Is this a rare or common request?
Precisely what is this plate called?
Where would I shop for it?
What should I be careful of?
Is it best to mount in on the front end or rear 3 point hitch to make it the most versitile?

Is it possible?

Sticky Clay

I am having a problem with clay build up in my backhoe bucket, 24 inch. After a few digs the clay build up on the sides, corners, back and bottom. Sometimes to the point that I am using only half of the bucket.
Help !
Any suggestions would be appreciated.
Old Uncle Dave

Sticky Clay

98 416C cat backhoe, what engine oil and filter, and capacity

Hi, I don't have my manuals anymore. What oil, and filter should I be using? What is the capacity and how often should it be changed? Thank You
ps, I have some cat filters that came with the machine but not sure what they are for so if I could get a oil filter number, that would be great. Also fuel, trans and hydraulic filters too. I guess I could check with the dealer when they open.
Thank you

98 416C cat backhoe, what engine oil and filter, and capacity

Champion 720 series 1

Hi guys,

I'm an owner/operator of an aerial spraying business in sask, looking at purchasing a 720 series 1 champion grader with the Detroit engine and standard transmission. The grader would be used to maintain a mile long dirt landing strip as well as some odd jobs around the farm. I also farm so have a fair bit of experience with farm equipment but I'm wondering if you guys can fill me in on things to look at on a grader other than the obvious things you look at on any piece of...

Champion 720 series 1

Champion 720 series 1

87 690d value

I've got an old 690d it's a 1987 with I believe around 10000 hours. It's not pretty and something with the hydraulic us a little off. They are plenty strong, just can't carry grade to save my life, it's great for pulling trees or bulking diet starts on the coldest days and runs out nice. I am thinking of upgrading excavators in the next 24 months. If I was to trade or sell this unit what would everyone consider a good value? Just figure it being rough in condition for your estimated value

87 690d value

1998 892e jd hyd. prob.

change gears on pump drive now motor under load 1998 892elc what did I short out

1998 892e jd hyd. prob.

British Columbia Forest Products Ltd.

Well HDX and Trakloader I grab the challenge starting this new thread British Columbia Forest Products Ltd.(BCFP) Company dates back to 1946. It was merged of several companies. Once it was the 3rd. largest lumber producer in Canada. Looking forward to see some great posts:canada
Now gone - it's a shame:(

British Columbia Forest Products Ltd.

1999 Hyundai 210 LC-3 monitor/cluster issues.

I recently bought a 99 hyundai 210 lc-3 which operates decently but the mode selection was kind of funky. I could only select H or F( supposed to default on S) .Initial testing revealed the cluster was faulty. The rest of the monitor functions and display works OK.
So i decided to purchase a new monitor from China cause they are half price of dealer price.
When i plugged the new cluster in it did nothing, it would not light up at all. When i contacted the seller he advised me to send it...

1999 Hyundai 210 LC-3 monitor/cluster issues.

1999 Hyundai 210 LC-3 monitor/cluster issues.

Kobelco SR 60 error codes?

Hi, I have a Kobelco SR60 Grand Beetle
SN# YT C1 03257
Have owned for a while with minimum probs. regular services etc.
Lately ;
After 1/2 hours work or so goes into limp and shows E20 and E21 on ECU
Won't stop on the key .
With engine stopped and key on , "FC" light flashes continuously .
If left overnight the machine starts and runs perfect again.
Any help greatly appreciated

Kobelco SR 60 error codes?

New from New Zealand

Hi All, awesome site, been a help already just reading some of the old posts.
Cheers

New from New Zealand

Looking to buy a screener. Suggestions?

looking to expand our business with the acquisition of a screener.

We screen compost/topsoil like material to 1/4” and 3/8” currently.

Thinking a powerscreen trommel may be good option. Anyone here on HEF have experience they want to share or suggestions for us?

Thanks all.

Looking to buy a screener. Suggestions?

Logging Shovels

Here is a video of a couple of log shovels in Weyerhaeuser's Vail sorting yard back in 1996. The yard was in process of being shut down at that time. The video was done because a dealership in Canada wanted to show people up there how our type of grapples worked.



Logging Shovels

953C 2ZN

machine travels either direction and suddenly stops; the trans light comes on. When you return travel lever to neutral the light goes out and you can travel again, but then happens again. Hydrostat charge psi is good and no service codes, oil level is full. Anyone experienced this before?

953C 2ZN

Difference between D6H lgp & D7H lgp

what is the difference between d6h lgp & d7h lgp , both w/ straight blade & diff steer .

Difference between D6H lgp & D7H lgp

What Grader Make Is This?

I have been searching the internet trying to identify this brand of grader but can't find another one that looks like it for identification. Can someone please identify what make/manufacturer and possible model this grader might be. I think it has a diesel engine. Any idea of the approximate year and value?

View attachment 174338

What Grader Make Is This?

Boom won't lift

we have a Timberjack 608 track feller buncher, which I could of posted this in the forestry section but a feller bunch has the same operation as an excavator, from time to time the main boom cylinder will not raise. It will lower but pulling on the joystick it will not raise the boom then in 10 seconds or sometimes longer holding on the joystick it will finally raise & then be fine for 15-20 minutes & then do it again. Seems to happen more once oil is warm. Anybody have any suggestions on...

Boom won't lift

Boom won't lift

D333 Engine

Does anyone know what the oil capacity is on a D333 Caterpillar engine? I read that it is 7 Gal. in manual. That seems too be to much considering I put 6 Gal in to start and it was about a 1/4" below full mark running at low idle. Then added 1/2 Gal to bring it up to 6 1/2 Gal and its a tad over full mark now. Also anyone that has experience with this engine, what type of engine oil are you using? Application Caterpillar 966A wheel loader. Thanks.

D333 Engine

http://ift.tt/2rPKBd0

Pro bowl 2018

Pro bowl 2018 Live

Pro bowl 2018 Live Stream

Pro bowl

Pro bowl Live

Pro bowl Live Stream

https://probowll2018.com

https://probowll2018.com

https://probowll2018.com

https://probowll2018.com...

https://probowll2018.com

http://ift.tt/2rPKBd0

John Deere 310d backhoe

I have a 310d John Deere backhoe ser#to310df774954 and my question is it was in 4 gear and locked up in the middle of the road with out any noise or anything and now it will only move in first gear any help with what it might be would be appreciated

John Deere 310d backhoe

Grammys 2018

Grammys 2018
Grammy Awards
Grammy Awards 2018
Grammys
The Grammys
Grammy Winners
Grammy Nominations
Grammy Awards Live
Grammy Awards 2018 Live
Grammys Live
The Grammys Live
Grammy Winners Live
Grammy Nominations Live
Grammys 2018 Live Stream
Grammy Awards Live Stream
Grammy Awards Live Stream
Grammy Awards Live Stream
Grammy Awards 2018 Live Stream
Grammys Live Stream
The Grammys Live Stream
Grammy Winners Live Stream
Grammy Winners Live Stream
Grammy...


Grammys 2018

Grammys 2018

Genie Z60/34 boom lift

I have here a Genie Z60/34 boom lift serial number Z60-3551 with 2370 hours on it. That somedays the swing is good in either directions .Other days it so slow in either directions.Anyone have any ideas.

Genie Z60/34 boom lift

Genie Z60/34 steer problem

Hi Everyone

I am having a problem with our Z60/34 serial: 7890

The problem started with the fact that when the machine moves forward the wheels spontaneously turn left.

I changed the drive-steer joystick and VALVE,SOLENOID 3 POS,4 WAY (p/n 111703). The joystick was calibrated after change, but after a short time the error 61-17 occurred (steer joystick not calibrated). I calibrated the joystick again and again. Then there is an error 61-16 (steer joystick value at 0V).

Currently...

Genie Z60/34 steer problem

Genie Z60/34 steer problem

TB 175 10 second shutdown

2005 tb 175 starts runs 10 seconds shuts down new computer and oil and coolant sensors problem still persists oil light /coolant light still flashing

TB 175 10 second shutdown

Preventive Maintenance KPIs

Hidear all,

I trust you are all well !
I request your help regarding the optimization of preventive maintenance on heavy equipment (dumper, dozer, loader etc).
I would to have a list of metrics or KPIs , ( like the schedule compliance for instance) to “measure” the preventive maintenance. It would be very helpful If I can know on which basis to calculate those metrics and how to do it (daily , weekly, monthly, on a group of machines?). Any help would be appreciated.

Thanks in advance

Preventive Maintenance KPIs

Michigan 175B Wheel Loader

View attachment 177309 Greetings all.
First time poster, long time reader...

I bought a Michigan 175B loader 2 and half years ago, knowing it had a torque converter issue. 2 years later we've afforded the TC rebuild complete with imported parts (to Queensland Australia). We put her back together last week, but found transmission dipstick missing from end of cap. Called a mate who has same loader, he too missing the dipstick...
Found another loader 4 hours away, "surprise, suprise"...

Michigan 175B Wheel Loader

Michigan 175B Wheel Loader

Michigan 175B Wheel Loader

View attachment 177309 Greetings all.
First time poster, long time reader...

I bought a Michigan 175B loader 2 and half years ago, knowing it had a torque converter issue. 2 years later we've afforded the TC rebuild complete with imported parts (to Queensland Australia). We put her back together last week, but found transmission dipstick missing from end of cap. Called a mate who has same loader, he too missing the dipstick...
Found another loader 4 hours away, "surprise, suprise"...

Michigan 175B Wheel Loader

Michigan 175B Wheel Loader

Huber-Warco 4D

samedi 27 janvier 2018

Looking for a clutch assembly any ideas?

Huber-Warco 4D

case 480c shuttle shift

I have a new to me case 480 c. I bought if from a younger man who got it from a grandfather passing, he new nothing about it, was just selling it. It starts right up, no smoke, good power and hydraulics work well. When I tested it, it drove forward and backwards fine. To get it to go in reverse, the column shifter, was hard to pull the shifter back. I get it home and now the column shifter will go forward and into neutral. It wont let the shifter be pulled back to reverse.

I follow the...

case 480c shuttle shift

case 480c shuttle shift

Volvo EC15B more problems

Volvo EC15B XTV older machine but low hours 600ish

Starts & runs for a couple seconds then instantly shuts off.
If i hold the key in start position is stays running until i let off, then dies right away.

Most of what ive read says that it is an electrical issue? Solenoid perhaps? Relays?

Recently changed my fuel filters, not sure if an air lock could do that....ive already cracked the injectors trying to bleed the motor of any air locks

ive checked the battery cables, all fuses are good,...

Volvo EC15B more problems

Volvo EC15B more problems

Silly question maybe

hi all have a basic question about chain strength that I'm unsure about.
Ok so from what I can understand about rope and pulleys (without being to scientific) if a rope is run around a pulley, it will effectively double the capacity or halve the load on each strand. A quick qoogle search suggests that the single strand is under friction/compression etc so doesn't take the full load. Probably not doing a very good job of explaining but I'm sure you'll know what I'm trying to say lol.
Ok so...

Silly question maybe

Silly question maybe

Fuel Setting Information for D5B w/ 3306

After rebuilding the governor section of my fuel pump, I've been unable to find the referenced "Fuel Setting Information" for my dozer. See several books of this nature on ebay but none seem to cover these machines. Only older obsolete models and 3306 engines used in trucks. Is there an actual publication that covers the D5Bs / 25X machines or some other source where the data can be found?

Thanks.

Fuel Setting Information for D5B w/ 3306

D5B Hydraulic Pump Rebuild

My hydraulic pump is leaking into the crankcase now that I've re-sealed the tank and return lines properly. I see in the CAT parts book that there are two lip seals that can be replaced, but there are no other parts shown for the pump, except for a "rebuild kit" PN: 9J765. I don't see how you could remove the old seals without splitting the pump apart. The pump body clearly needs to be resealed, but there are no gaskets / seals shown in the parts book.

So, what am I missing. Does the...

D5B Hydraulic Pump Rebuild

D5B Hydraulic Pump Rebuild

Good portable garages?

I've seen people mention Shelter Logic but they don't seem too durable. I was looking up local companies and came across WeatherPort's portable garages. I guess I have to get a quote to get a price but before I do that anyone have any experience with them or any other suggestions?

Thanks!

Good portable garages?

Magnetic bubble level

I know I've seen those bubble levels on a grader for sale somewhere. I cant find one. Just a magnetic one that's big enough to see from the cab. Anybody use one or know who sells them?

Magnetic bubble level

royal bean pump sprayer water deicer

this huge pump is coming out of a la-1000 aircraft deicer ground service support truck. bean royal pump
it was driven by a ford 4 cylinder industrial gas motor.
it has perfectly clean oil in it and does rotate as it should when clutch is engaged .
vehicle had 900 hrs on working tach , which means this pump has way less actual pumping hrs on it !!!
im pretty positive this is medium pressure and huge volume.
could be used for a sewer jetter for large pipes washer cleaner ??? farm pto tractor ?...

royal bean pump sprayer water deicer

royal bean pump sprayer water deicer

D6m tranny priblem

D6m moves sluggish when cold. Moves full power when warm..has 11000hrs. Also 1 st gear works sometime...and sometime not.

D6m tranny priblem

Cat 302.5 and flail mower

Hey guys
Long time no visit
But here goes

At home I have 10 acres bit of a hill, bit of a creek line needs mowing and maintenance

I’m going to look at a 302.5c cat excavator (looked at many others this one is actually good compared to a lot of the used machines around here) to do this task

Now I’ve found a flail mower that will supposedly run on this machine
Has anyone ran this style of attachment on a 302.5c and how did it perform

Cheers, Matt

Cat 302.5 and flail mower

Please help Losing water freightliner with cat 3306 fld 112

Hello , first of all thanks for taking time to help out with your collective knowledge , have a dump truck original freightliner fld 112 , year 1995 with a cat 3306 , 8ll tranny and 456 rears , we bought the truck about 4 months ago its been doing great however we are loosing a lot of water on a weeks time about 4 to 5 gallons of water ( that's a lot of water ) facts : truck runs 300 to 400 miles a day sometime more , starts in the morning perfectly no white smoke , no engine misses hot...

Please help Losing water freightliner with cat 3306 fld 112

Please help Losing water freightliner with cat 3306 fld 112

Cat 302.5c and flail mower

Hey guys
Long time no visit
But here goes

At home I have 10 acres bit of a hill bit of a creek line needs mowing and maintenance

I’m going to look at a 302.5c cat excavator (looked at many others this one is actually good compared to a lot of the used machines around here) to do this task

Now I’ve found a flail mower that will supposedly run on this machine
Has anyone ran this style of attachment on a 302.5c and how did it perform

Cheers, Matt

Cat 302.5c and flail mower

8r sn 6yz00839 engine ecm problems

tractor was rebuild apx 5000 hr agao new all new wire harness was done by cat dealer at that time remaned all ecms since that time cat has replaced 5 yes 5 engine ecm all have given different problems . have had 3 different techs work on it all cat field service . I feel we are fixing the problem but not the cause .told them Friday no more reman ecm . will try a new one next week . but feel we are missing something . any one had this problem

8r sn 6yz00839 engine ecm problems

ROPS Bushings

Good afternoon gentlemen,

I've got a bit of an issue trying to find the correct ROPS bushings for my 977L (11K7981)
My parts book lists them as 8D18 however that number doesn't appear to be any good.

Any help would be greatly appreciated! See pic of whats left of the bushings below. View attachment 177290 View attachment 177291

ROPS Bushings

Case/carraro hub bearing preload

I'm just finishing up rebuilding the front axle on a case 580e (early design with 4 bolt kingpins)
After assembling left front hub with new bearings there is still some play between the hub and swivel housing not much but its there. Is there any way to adjust preload on the hub bearings? manual does not mention anything about setting axial preload other than tighten axle nut to 850ft pounds.

-thanks

Case/carraro hub bearing preload

Komatsu GD300A

Has anyone had any experience in sourcing parts or anything in general for these??

Komatsu GD300A

ISO used Tuxco HGS- 40 cylinder bench??

Looking for a used tuxco cylinder bench. 662-891-8483.

ISO used Tuxco HGS- 40 cylinder bench??

ISO used Tuxco HGS- 40 cylinder bench??

Looking for a used tuxco cylinder bench. 662-891-8483.

ISO used Tuxco HGS- 40 cylinder bench??

Hydraulic Cylinder Repair Bench

Building a hydraulic cylinder repair bench similar to the wtc small cylinder repair bench. The question that comes to mind is for the wrench’s in the past I have cut wrench’s out on-site of 1 inch plate. I had the crazy idea to use a large three jaw chuck off of a lathe. One size fits all. To turn it I thought of a sprocket segments welded to the outer diameter of the chuck. And a chain fastened to the hydraulic cylinder used to pull the chuck/wrench setup. The biggest question that comes to...

Hydraulic Cylinder Repair Bench

Hydraulic Cylinder Repair Bench

http://ift.tt/2rMucWm

pegasus world cup Live
pegasus world cup Live Stream
https://livetvstreamgame.com/pegasus-world-cup-live

pegasus world cup 2018
pegasus world cup 2018 Live
pegasus world cup 2018 Live Stream
pegasus world cup
https://pegasusworldcup-2018.com/live/
https://pegasusworldcup-2018.com/live/
https://pegasusworldcup-2018.com/live/
https://pegasusworldcup-2018.com/live/...


https://pegasusworldcup-2018.com/live/

http://ift.tt/2rMucWm

A recent job

View attachment 174776 View attachment 174777 View attachment 174778 View attachment 174779 Nothing like doing a job twice we took on this footing after another company figured out the rock was harder than they could handle they dug the entire footing out and exposed all the rock that was above grade at the concrete companies request and leave it for the guy that contracted the pad because he was responsible for the hard dig. needless to say he couldnt do it and...

A recent job

A recent job

PRO BOWL 2018 LIVE AFC vs NFC Live Stream

PRO BOWL 2018 LIVE

https://www.probowlnews.net/

https://www.probowlnews.net/

https://www.probowlnews.net/

https://grammyawardsnews.com/

https://grammyawardsnews.com/

PRO BOWL 2018 LIVE AFC vs NFC Live Stream

PRO BOWL 2018 LIVE AFC vs NFC Live Stream

http://ift.tt/2DPHlD7

pegasus world cup Live
pegasus world cup
pegasus world cup Live Stream
pegasus world cup 2018
2018 pegasus world cup
https://livetvstreamgame.com/pegasus-world-cup-live
https://livetvstreamgame.com/pegasus-world-cup-live
https://livetvstreamgame.com/pegasus-world-cup-live
https://livetvstreamgame.com/pegasus-world-cup-live
pegasus world cup Live
pegasus world cup
pegasus world cup Live Stream
pegasus world cup 2018
2018 pegasus world...


https://livetvstreamgame.com/pegasus-world-cup-live

http://ift.tt/2DPHlD7

99 Peterbilt 379 worth (Insurance)

My brother in law (Bo) has 99 Pete, 6x4, heavy springs, C15 motor with sleeper and chrome every where. Has taken great care of the truck and had just had the motor rebuilt. Two weeks later some guy comes around the corner and hits him head on. Everybody is OK and the other driver even admitted to the cops that it was his fault.

The truck has a busted front axle, steering box, bent hood and others. Estimate to fix the truck is 38K and the insurance wants to total it saying its only worth...

99 Peterbilt 379 worth (Insurance)

99 Peterbilt 379 worth (Insurance)

cat 303 emergency stop pull

Looking for some help.
Can anyone tell me how to reset the emergency stop switch?
It was pulled on acciedent.
It appears to go to fuel pump but I don't see any way to access it. Looks to be a simple fix it I couuld get to it.
Do have to pull the engine?

Any advice would be great.
Thanks

cat 303 emergency stop pull

Australian Open 2018

Australian Open 2018

Australian Open 2018 Live

Australian Open 2018 Live Stream

Australian Open

Australian Open Live

Australian Open Live Stream

Australian Open Final

Australian Open...

Australian Open 2018

Australian Open 2018

http://ift.tt/2GjLQ7g

pegasus world cup 2018
pegasus world cup 2018 Live
pegasus world cup
pegasus world cup Live
pegasus world cup Live stream
pegasus world cup Live stream
pegasus world cup 2018 Live stream
The Pegasus World Cup
The Pegasus World Cup 2018
2018 Pegasus World Cup
https://pegasusworldcup-2018.com
https://pegasusworldcup-2018.com
https://pegasusworldcup-2018.com

pegasus world cup Live
pegasus world...


https://pegasusworldcup-2018.com

http://ift.tt/2GjLQ7g

Gooseneck coupler hitting slip tank

Recently put a slip tank in my 3500, and upon hooking up my gooseneck for the first time, I forgot to account for the bolts in the coupler, and there isn't enough clearance. Upon turning left with the trailer/truck at a difference in height the one bolt just catches the tank. Only took off some paint, but need to change something because i'm not ok with that.

As you can see in the picture there is some room there, but not much. Is there some easy way to put in shorter bolts? If I could get...

Gooseneck coupler hitting slip tank

Gooseneck coupler hitting slip tank

Finding qualified help

Is any one else having a hard time finding CDL Drivers or Experienced equipment operators? This year the pool of talent seems to be getting smaller, with many old timers retiring, there do not seem to be many young guys or girls getting into the industry.

Is this an industry wide problem or is it just in New England?

If you have experienced this what have you done to encourage new comers to the industry?

Sorry if this thread already exists but I did not see it.

Finding qualified help

JLG Boom Lift hydraulic "slack"

I was using the 600A yesterday. Drove it to the worksite about 1/2 mile. Then, I rose the main boom, and telescoped the fly boom almost to full extension.

The lowest tower main Boom Assembly then rocked forward causing the whole upper section to drop suddenly.
Thankfully I was secured in the basket and had a hand on the cage.

I then retracted the fly boom, which caused the balance to change and the Boom Assy then rocked back to lowered position which was another catapult ride in the...

JLG Boom Lift hydraulic "slack"

JLG Boom Lift hydraulic "slack"

DT 466B tapping and knocking

My bob tail dump is a 1979 International with a 466B (round injector pump), an Allison automatic, and a two speed rear axle. It started life as a public works park department truck and I got it with mileage around 62,000 & 8900 hours. In the 17 years owned - put on 17,000 miles: about 1000 miles per year. Best year was 1500 miles! Economy w less work lowered annual miles to around 500. Today it has 79,000 miles and 9900 hours.

I change all the filters regularly, monitor the green...

DT 466B tapping and knocking

DT 466B tapping and knocking

How do you deal with difficult customers?

Hi everybody, here's a question of a more philosophical nature rather than technical. For all you owner operators who do little jobs for people around the way, what do you do for people who want you to do things that are dangerous or abusive for the machine, or want a big expensive job done way faster and cheaper than is possible.

The first situation I generally attribute to over hopeful ignorance about what these things can do and how expensive it is to fix them.

The second situation,...

How do you deal with difficult customers?

How do you deal with difficult customers?

Hitachi ex100 questions

So I gambled a bit today and bought an ex100 that is missing a starter and possibly has other electrical issues. Where can I find the serial number to determine what machine age is? It has the isuzu motor. It is tagged bd1pz but looks like it is missing the first digit. Is the electrical system all 24 volt? It is also missing the batteries. What is a good source for a new starter? View attachment 177111

Hitachi ex100 questions

IH/Dresser 412B wheels

Greetings all,

Our pan restoration project is coming along nicely. What we feared to be locked engines turned out to be starter solenoids fried by jumping with low voltage. One of the 2 is running and functioning fully with very little blowby and only a few hydraulic leaks. The other will probably need a little more love, but looks promising.

We had a tire service come out to replace a couple of the 23.5 x 25 tires and the tech said one of the rims was too far gone to save. Does anyone...

IH/Dresser 412B wheels

IH/Dresser 412B wheels

no risk no gains in life

NHL All Star Game 2018 Live Stream
NHL All Star Game 2018 Live

no risk no gains in life

Wabco scrapers at work

With all the talk about big scraper operator's in California, thought I would give everybody a change of pace. Richardson Contracting out of Columbia South Carolina is still moving dirt with a fleet of Wabco 229F, 339F scrapers. These pictures were taken several years ago in Anderson, South Carolina. I think it was about a million yards at the local airport. They also have 5 TD-40 Dresser dozer for push loading duties. I believe Richardson still operates a fleet of over 30 Wabco's. It's...

Wabco scrapers at work

Wabco scrapers at work

Komatsu ripper

vendredi 26 janvier 2018

Hi, I'm looking for some information on a ripper, the ripper plate read Drp80-115910 and the cylinder head # is 154-78-11211, I don't know what machine did it came from, can you guys help me out, I need the seal kit part# and head seal dust part#.
Thanks

Komatsu ripper

Horton fan cagenut

I am going to replace the bearing and stuff in a Horton clutch and it says i need a cagenut 17310 is it lefthand thread?

Horton fan cagenut

Anybody make their own cylinder bench?

I've started to look at building my own cylinder bench and would love to see guys who have done their own to get some idea.

Anybody make their own cylinder bench?

Royal Rumble

Royal Rumble

Royal Rumble 2018

WWE Royal Rumble

Royal Rumble Live

Royal Rumble 2018 Live

WWE Royal Rumble Live

Royal Rumble Live Stream

Royal Rumble 2018 Live Stream...

Royal Rumble

Royal Rumble

The JLG 40F Boom Lift Dilemma

I started talking about my JLG 40F in 3 other forums. I needed to post at least 3 times before I was allowed to post my own thread. Sorry for the inconvenience. Here are the issues. First JLG gives no support on the E or the F series. If you go to there Manual’s down load area they are not even listed. They do list some parts though. As for service they have not returned 1 of my phone calls. I did receive an email reply from them. It was a link to there dealer and service people. All of the...

The JLG 40F Boom Lift Dilemma

The JLG 40F Boom Lift Dilemma

Morooka mk

Good morning. I'm searching for a hydraulic pump or a part of this for my mitsubishi mkm70, its the same as Morooka mk70. Can help me? The pump is an Uchida-Rexroth A10VG43HW. Only need the rear case. Thanks

Morooka mk

Grammy Awards 2018

Grammy Awards 2018

Grammy Awards

Grammy Awards 2018 Live

Grammy Awards 2018 Live Stream

Grammy Awards Live

Grammy Awards Live Stream

Grammy Awards 2018

https://thegrammyaward.com/...

Grammy Awards 2018

Grammy Awards 2018

new vid dismantling crane

Enjoy watching a new video from me
i hope you guys like it never recorded like this before but it looks very nice

https://www.youtube.com/watch?v=lfw085a ... jrk0h00410

new vid dismantling crane

late 80's schmidtt airport brooms for sale ( 2) brother and sister

need opinion's on what you guys think i should do? sell these out right ? put them back on auction? whatever?
heres the story. i'am a retired snow contractor mechanic and now i sub my-self and my equipt to others that do large propertys well last year i just ran myself and my loader that is fine ( but gets boring) then i seen these on the auction. well the mind starts spinning. i shred and sell top soil and figured in between during summer id turn one of these into a 3 plow with brine...

late 80's schmidtt airport brooms for sale ( 2) brother and sister

late 80's schmidtt airport brooms for sale ( 2) brother and sister

Pair of Northwest machines

I been thinking about selling my pair of 3/4 yard Northwest machines.
Both are running and operating machines. Both taking up space in my building .That is why they are so dusty/dirty . I am asking $8000 each or $14000 for both. Machines are in Virginia. If interested send me a message . Thanks for looking. View attachment 171469 View attachment 171470

Pair of Northwest machines

Greetings from Germany - How to separate Backhoe from Machine?

Hello together...

and first greetings from Germany!

I´ve bougt an 1979 CASE 580 F (European Version), this powerfull Machine :) works very fine, but i have an understanding trouble.

How can i separate the backhoe arm from the rest of the Machine, is there any manual in the web? Especially the separation of the hydraulic hoses seems tricky to me.

best regards

CASE580FUser

Greetings from Germany - How to separate Backhoe from Machine?

AVN Awards 2018

AVN Awards 2018

AVN Awards

AVN Awards 2018 Live

AVN Awards 2018 Live Stream

AVN Awards Live

AVN Awards Live Stream

2018 AVN Awards

2018 AVN Awards Live

AVN Adult Entertainment...

AVN Awards 2018

AVN Awards 2018

Here's a bit of history-still happening-FMC/KMC

We just sold three FMC/KMC tracked skidders that we converted into forestry firefighting machines some time back. They're an interesting machine that might have had a future in logging if some of the early problems were fixed sooner.

They were originally built by FMC, and based off of one of their military tracked carrier designs. FMC made about 1100 of these things before selling the rights to KMC, based in Nelson, BC in about 1988. KMC is still around today but I'm not sure just...

Here's a bit of history-still happening-FMC/KMC

Here's a bit of history-still happening-FMC/KMC

Special attachment for back-filling deep holes?

Got a job coming up that requires us to backfill 3' to 6' diameter holes, 50' deep, with sand.

Typically I would just use a loader bucket, scoop, dump and push the sand into the hole.
But considering we will be doing several holes a day, with LARGE quantities of sand, I want to optimize the process.

Is there a good loader bucket attachment with some sort of funnel that I can place directly over the hole so there is no spillage on the sides of the hole?

Is there a possible better piece...

Special attachment for back-filling deep holes?

Special attachment for back-filling deep holes?

First time pulling tranny

I am pulling a tranny on a truck for the first time ever the clutch has an issue it's on a 99 Mack RD688S. Any pointers or is there something else to engine, clutch or tranny I should do?

I have a pit in shop I'm doing it over that I put a track or rail in when we did the concrete work and i already made a lift to put in a diff on another truck and was planning on adapting it to pull the tranny so if I can lower the tranny low enough will I be able to pull it with out pulling the shift...

First time pulling tranny

First time pulling tranny

Case 580L series II service manual

Anybody have one they would sell, copy, pdf to me etc... I really need one and cant order it from the dealer and i have been looking for 6 months with no luck yet. Any help would be appreciated.

Case 580L series II service manual

CAT 257B3 electrical - Front door safety

I have a 2011 257B3, everything works when the dummy/jumper plug for the front window is plugged in. Once I plug in the connector for the door, nothing works as if its not plugged in ( no hydraulics, wiper etc) no broken wires behind door cover, everything seems to be intact. Any ideas on where to start would be appreciated, Fuses are good, not sure if theres a relay or not or which it would be. is there a safety switch that I can check, my 246C has one on the door but I don't see one on...

CAT 257B3 electrical - Front door safety

CAT 257B3 electrical - Front door safety

Plenty of paddle pans

Last Friday morning I had zero paddle pans (which may prove to be the perfect number to have). Today I have 3;
Dresser 412B and IH 412B and Cat 615 46Z machine. The Cat needs batteries but seems to run pretty well, the 412's have been owned by a local contractor for the past 20 years or so and not run for a couple of years. They need batteries, a couple of tires between them, and a hoses at first glance. Both 412's refuse to turn over with fresh batteries, engaging the solenoid (I assume)...

Plenty of paddle pans

Plenty of paddle pans

you are succes in life & enjoy your time

https://grammys2018i.com/
https://grammy-awards-live.com/

you are succes in life & enjoy your time

Grader Tires

jeudi 25 janvier 2018

Ok county guys and gals,what tires are you running? Which ones give you the most bang for your buck.

Right now we have 4 machines still on 14.00X24 and 1 on 17.5X25.We seem to have the best luck with Bridgestone VKT on our 14.00 machines.But now its about time to shoe the 17.5 machine so was wondering what others have been having good luck with.

Grader Tires

Cat 951-C in my sights

I have some work to be done on my farm, 35 acres that I have owned and have lived on for more than 40 years. I need to clean out a 1 ½ acre lake that has accumulated about three to four foot of silt after 25 years. It does have a solid rock bottom under all of that silt. I also need to do some spillway work. I have roads to repair and culverts to install. I need to ditch the upper side of some of the roads. I also have some trees to take down for the saw mill and some stumps to remove from...

Cat 951-C in my sights

Cat 951-C in my sights

old Italian construction site with old vehicles

I include photos old plant for packaging with old concrete mixer trucks astra worghton, loaders fiat excavators Laltesi positioned near the creek bed View attachment 153056 View attachment 153057 View attachment 153058 View attachment 153059 View attachment 153060

old Italian construction site with old vehicles

Deere 550J LT for clearing right of way in mesquite

I need to clear right of way through mesquite in West and north Texas. No huge trees mainly 10” or less but thick at times. No serious terrain or major dirt work involved. Right of way just needs to be adequate for a side by side UTV to travel it a couple of times. Most jobs would be anywhere from 1-20 miles of right of way.

Would this sized machine be adequate for this or will I need something larger to be able to do it at a reasonable pace? I would like to be able to clear 2-3 miles a...

Deere 550J LT for clearing right of way in mesquite

Deere 550J LT for clearing right of way in mesquite

Timber Cutter Magazine

I remember Finley Hays published this in the 70's & 80's.
Anybody else remember it?
Anyone have any copies still?

Timber Cutter Magazine

Halitrrax

I have a New Zealand built track loader with a vickers TA1919V20r pump, the charge pump pressure is 190psi, when you go forward the pump starts to rock that badly that it seems that the motor and pump are going to break of the engine mounts, if you drop the revs it most time stops rocking. Change filter checked suction line, checked relief valve, cleaned hydraulic tanks and I can not find a strainer on suction line to charge pump. any ideas cheers mic

Halitrrax